Jump to content
SAU Community

Fs: Remote Control Car *melb*

Alexxs

By Alexxs,
in For Sale (Other Items)

 Share

Recommended Posts

Alexxs Community Regular

Alexxs

Posted
Posted

Remote control car 1:10 scale of Subaru WRX STI 4 wheel drive model.

running on a 5% ethanol pre mixed fuel available from hobby shops, do not use petrol!

this car little bit dusty as was driven on gravel / loose ground.

comes with a whole bunch of extras still about 3.5 liters of fuel, 2 starter battery, spare glow plug. whole new wheel / rim kit was put on this car for better road driving. along with a recent service of new air filter, glow plug, fuel filter and fuel lines. Comes with a simple to use, remote control, left right and accelerate, with interchangeable idle speeds on the remote. One tank of petrol around 200ml lasts about 20/30mins of drive time, depending on how hard the car is pushed, and engine configuration. top speed of around 60km, hard to say thought have never had a large straight road to fully unleash the engine on.

Drives perfectly, easy to tune the engine and play around with fuel / air mixture to run lean or rich. A all round great car, the car is 4wd and has interchangeable shell, available from most hobby shops.

For local pick up only, as too bulky to post, too many loose items, if desperate can arrange postage *however the fuel CANNOT be posted*. Victoria, 3150.

Melbourne pickup 3150, south east, or can deliver to most eastern / south eastern suburbs for petrol costs.

Asking price is $350 *ono*

2m7epvq.jpg

sylgcw.jpg

6ir701.jpg

20jssqq.jpg

Link to comment
https://www.sau.com.au/forums/topic/271484-fs-remote-control-car-melb/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • dbm7
      Automatic Power Button Light Flashing

      By dbm7 · Posted

      Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Duncan
      R34 Plug Identification

      By Duncan · Posted

      Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • joshuaho96
      Automatic Power Button Light Flashing

      By joshuaho96 · Posted

      Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...