Jump to content
SAU Community

Recommended Posts

Congratulations to Ben (Grim) and Nene, who today discovered Nene (14 weeks preggo) is expecting a boy!!!

Not entirely car related ... but I'm sure the young lad will inherit the imports in Ben's garage ... so it kinda does :)

Could the kind merciful Mods allow this at least 24 hours of life before closing? :)

On another note Nene, being 14 weeks pregnant is no excuse for not getting to me your membership forms :D:P

Edited by RubyRS4
Link to comment
https://www.sau.com.au/forums/topic/271870-heir-to-the-imports/
Share on other sites

  • Replies 70
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

how did they determine the sex at 14 weeks?

even with 4D they could only just determine that ours is a boy.....

not because he has a small cock or anything but just because its hard to tell so early in the pregnancy...

but congrats to them none-the less.

thread about a pregnancy

1st poster - pelvic thrusting aviator

2nd poster - ultra sound image

kidafa - u let us down with your aviator, but i guess the kid part follows

ill shutup now, congrats :D grim jr it is

and i think his 1st ride should be this 1 :P

post-31501-1243338600_thumb.jpg

Edited by Inline 6
:D

does it make me some sort of pedo to refer to it in that way?

pllllllease.

dont be so sensitive steve.

+1 does everything have to be sexualized by the sexually repressed?

-D

EDIT : Would u prefer us to refer to it as a ding a ling, a ding dong, a doodle, a wing wang, a johnson or would u prefer clinically accurate terms such as phallus?

Edited by Dohmar

really no need to be like that just saying i stand by my convictions

guarantee if Pete had of said what i said it would of been a different story

DON'T worry i take offense to Pete saying a little bit of wee came out too don't think that was entirely needed either

its ur son, u own him, say what u want about him :)

must have a bigger dong than my little one then :P

we had the 4d @ near 17 weeks and they where only 80% sure...

the 20 week scan confirmed.

something to tell him when he's older if he ever gives u shit :P

edited by SLED

didn't you read my post Dan.....stop ya stiring bro

edited sled post edited by dan

no i didnt, i posted it while your were posting ya post, post post post

and no i didnt edit your section to spell edited wrong :)

Edited by SLED

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...