Jump to content
SAU Community

Recommended Posts

I have a stock R31 auto, bought as a daily car so 33 gets a break.

Last week i pulled home realising that it was overheating and it was boiling so much i could hear it spilling into the overflow bottle.

I have done a radiator flush but no change, taken in to radiator place and he reckons its a blocked radiator but when undoing the bleed bolts nothing comes out and all other pipes besides the 2 from the radiator are hot. Also pipes going into heater are pretty dry.

Just after any help as im stumped and dont want to put it into a shop as will cost a fortune in labour.

Am gonna pull it apart on the weekend and check radiator, also pull off all pipes and check thermostat....

If you have had this trouble or can help i would appreciate it.

Thanks

Brad

Link to comment
https://www.sau.com.au/forums/topic/272225-overheating/
Share on other sites

If you're mechanically minded best part is to work from your engine back.

I couldn't tell you whats wrong as I can't physically see whats the deal.

Basic elimination brother i'm afraid.

Oh...simple, but...is there coolant going fromt the overflow bottle into the radiator?

I have once found a leaf in my bottle in my van, f**k knows how it got in there, but it caused the coolant to stop flowing out.

Hope that helps.

RJ!

Link to comment
https://www.sau.com.au/forums/topic/272225-overheating/#findComment-4623293
Share on other sites

Yeah the water is filtering into the radiator and there isnt any leaks, guess only thing i can do is pull it apart and hope i find something.

Guy at radiator place felt the 2 top pipes and said coz they are hot that the thermostat is fine and that he rackons its a blockage...

The fact that the other pipes coming from the engine arent hot i think it may be something else. The bleed bolts should leak air or coolant right?

Link to comment
https://www.sau.com.au/forums/topic/272225-overheating/#findComment-4623305
Share on other sites

my car was doing the same thing i replaced everything. new water pump, thermostat hoses etc etc.. turns out the rad was blocked solid cos i used cheap shit coolant from woolies. i got it cleaned at a rad place and is great. cost me $135 including labour to pull it out etc. take it out urself and take it in tell them the core is blocked you want it strip cleaned. where they take the tanks off and jam a strip of stainless into every core to clean them. i wish i had done that first wouldve saved me a lot of money and heartache.. give it a shot mate

Link to comment
https://www.sau.com.au/forums/topic/272225-overheating/#findComment-4623396
Share on other sites

I simple check before your spend any money would be to remove your thermostat... chuck a pot of water on the stove... ideally if have a thermometer you can keep an eye on how hot the water is getting.. place the thermostat in the water and see if it opens.

Link to comment
https://www.sau.com.au/forums/topic/272225-overheating/#findComment-4625047
Share on other sites

If you're going to boil the thermostat;

- of course if it doesnt open at all with boiling water its stuffed

- just because it opens in boiling water doesnt necessarily mean its opening at the right temperature. So its best to have the a thermometer. Not sure what the opening temp will be, but i'd guess about 70, definitely less than 85.

You could also just remove the thermostat and go for a drive, tho it will take much longer to get up to temperature, so dont thrash it early.

Link to comment
https://www.sau.com.au/forums/topic/272225-overheating/#findComment-4626191
Share on other sites

have the taken the car to get looked at yet??

first of all dont take it anywhere without using a pair of pliers/screw driver and ur garden hose

there should be coolant coming out of ur bleeder screw!!! if there isnt.... put the hose into the radiator until water comes out then refitt the screw.

pull both your radiator hoses off (at engine end) and pump the hose in it full blast and see if u get as much coming out as u are pumping in..... if it seems like ur not, the radiator could be blocked....

put it back together and do the same process on ur two small pipes going to the firewall..... put the interior heater swtich to HOT, take both hoses off from the engine side, pump the hose in one end and see if the same amount of water is coming out the other hose..... if its equal flow then ur heater core isnt blocked....

if both of those looks good, pull ur thermostat out , put it back together minus thermostat.... fill with water and let it bleed the air out then go for a drive and see wot happens....

do that b4 u take it anywhere and post results

Link to comment
https://www.sau.com.au/forums/topic/272225-overheating/#findComment-4626489
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
    • Yeah, I would have said the same. It makes me suggest that there are other things wrong, such that the ECU is totally unhappy with the broken sensor. The only other thought here is that maybe it is shorted, which might cause a different issue to the typical "disconnected" sensor.
    • The fact that US/JDM plates actually fit the skyline bumpers properly is a big, big thing for me as they are the correct dimensions. Annoyingly you can't opt for a normal plate (or plate combination) in that size. You have to make up your own one, and at that point you'd still know it wasn't randomly assigned. 
    • Well, really, that's any ECU, because it's not so much the ECU that the tuner connects to, but a laptop that's connected to the ECU. You have to have the tuning software installed locally. The "remote" part is essentially just remote desktop (RDP) or VNC type access. Nevertheless, if you're looking to upgrade, then you're immediately in the Haltech/Link territory, both of which can be done by any number of competent tuners here in Oz. But without a dyno, you'll definitely also need a wideband O2 sensor fitted, and you'll probably be relying on "auto" tuning a bit, where you drive it around under various loads and then apply the corrections that the ECU learns (basically applying the fuel trims that the ECU has to do to correct the mixtures). Tuning the timing is a little harder. It can be difficult to trust the old OEM knock sensors on RBs, so it is definitely best to have someone who knows what they're listening for, with knock ears (a piezo microphone connected to the engine, and and little amp and headphones so the listener can hear the angry men with hammers who live in the engine). That is more difficult to do remotely, and I suspect the only sane way is to be quite conservative on timing. But that's OK. You're probably waaaaay better off with conservative timing where you are. What is the fuel situation? 98RON available? Or low grade jungle juice?
    • I see your point, I didn't think too deep into it, was purely focused on the price. There's no bad blood between myself and GSM, they acknowledged the price was cheaper else where and at the time couldn't match it. 
×
×
  • Create New...