Jump to content
SAU Community

Recommended Posts

What about the "Apexi Power FC" unit??? Doesnt this override the R33 motherboard, allowing the Speed limiter to be taken off and also allowing higher performance tuning.

It's a whole new ECU. You take the stock one out and put this tuneable(new word) ECU in.

A lot more expensive and hard to get. Wasn't there some guys over east making patch looms to use GTR powerFCs on 33's?

XSpeed can hook a GTR Power FC Djetro to your GTST. It's just going to cost you in labour to rewire.

interesting to hear that a standard ecu will loose its remap if disconnected from battery??

can any one confirm this???

Yes! Goes back to the base map and the ECU will 'relearn' a little bit.

Yes! Goes back to the base map and the ECU will 'relearn' a little bit.

well that explains it. i took my battery out a few weekends ago. makes logical sense. should of thought about that before i left my lights on lol.

It won't reset by just unplugging the battery, as the ECU will retain a little bit of charge in there..

You'd need to have the battery off for like 24 hours maybe??

Or you just take the ground wire off the battery, go step on the brakes a few times to drain whatever power is left in the system, and it should be reset.

A remapped ecu WILL NOT lose it's remap if battery is removed. The maps are burnt onto an EEPROM.. losing power does not wipe these.

It might be the case for a piggyback unit like an SAFC but I've removed my battery plenty of times and my remapped ECU hasn't lost its' maps..

  • 5 weeks later...

if your unsure, get a memory minder. plug it into your cigarette lighter, connect the connectors to another battery and it will keep all settings the same and saves you having to set any electronic part all ovr again( not saying it could involve ecus but radio codes, shift light settings, etc)

  • 3 weeks later...

Nistune boards use EEPROM backed NVRAM... so settings are stored permanetly. I'm sure powerFC would use FLASH or something similar

Only settings that get lost are really O2 sensor closed loop and alpha learn trimmings and DTC codes which get stored in the ECU

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...