Jump to content
SAU Community

Recommended Posts

Hey guys,

Going to be buying the rack end spacers for more lock and thought i might aswell grab the alloy steering spacers aswell while im at it - http://www.gktech.com.au/products/index.asp?ID=159

Anybody have these fitted to their car? Are they worth buying? How do they alter the cars handling/steering exactly?

Just want to basically know if they are something to stay away from or even a must to buy...

Thanks

Link to comment
https://www.sau.com.au/forums/topic/272603-alloy-steering-spacers/
Share on other sites

I think your talking about the rack spacers Nisskid. He is talking about just replacing the factory rubber steering joint with a solid alloy one. It won't change lock.

Yep, thats right.

Soooo.... should i or should i...? What do i get out of em??

It just stiffens up the loose feeling through the steering wheel due to old worn out rubber mounts giving a more direct steering feel. I know people have done it and could feel a difference (in old S13's) so for the price its probably not too bad to freshen up the steering but apparently its a shit job putting it in unless you have the gearbox or motor out. Doable, just a shit job.

Hmm hard to answer. If they know what they are doing I don't see why they couldn't get it done within the hour ($80) but if they put the apprentice on it could end up costing you more.

Unless your installing it yourself it starts to seem like a lot of money to just take a bit of slop out of the steering.

I think your talking about the rack spacers Nisskid. He is talking about just replacing the factory rubber steering joint with a solid alloy one. It won't change lock.

lol oops, i just saw the link to GKtech and knew he sells them.

they basically replace the standard rubber item with a metal one, so u increase the response and get rid of a bit of play in the steering.

Put the spacer in my car today, on a scale of 1-10 of difficulty i'd go with a solid 9, (10 means I had to break out the angle grinder and cut stuff off). I'm an aircraft mechanic by trade so I like to think I know my way around nuts and bolts as well. Appart from the fact it's in a flamin mongrel of a spot and unless you got skinny little arms like me you'll have to do it all from the bottom, the nuts are done up god damn tight. I undid the two bolts with their heads towards the firewall and undid the spline where it goes into the rack uni so I could take the whole shaft out and do the other two bolts out of the car. It would probably be slightly easier to do from under the car as there is a little more access, you do need to get someone to hold the steering wheel though while your undoing and doingup stuff cos the lock on the 32 only engages when the wheel is straight....kinda gay. Oh and to crack the nuts stick a ring spanner on the nuts, hold it and get someone to turn the steering wheel :blink:

post-14136-1243929295_thumb.jpg

post-14136-1243929328_thumb.jpg

post-14136-1243929364_thumb.jpg

worth the effort, and Omurru you got the good spacer, the one you have is the proper designed one,

they are not that hard to do, just have to be willing to stretch the arms and have some muscle to get them out.

i have replaced quite a few of these with the spacers i make.

they are not that hard to do, just have to be willing to stretch the arms and have some muscle to get them out.
unless you got skinny little arms like me

lol maybe thats my problem :) Haven't driven the car yet but will see how we go.

And lol at this forum changing words ( I didn't write flamin mongrel above :rant: )

flaming oath you must have!

these solid mounts make a huge (noticeable) feel to steering response. A+++ would buy again.

easy to do when the motor is out. an utter bastard to do when the motor is in - give it to an unsuspecting mechanic to do :)

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...