Jump to content
SAU Community

Recommended Posts

G'day

my stagea has just clicked over to 85000 ks and with the snow season just around the corner i figured i should get any major service work done sooner rather than later

The car is pretty much standard with hi/lo boost switch and a pod filter... its a series 2 stagea (rb25 neo)

What i was thinking of doing was the following

- timing belt

- spark plugs

- clean pod filter (k+n)

- oil change

- bleed brake system / new brake fluid

- usual check fluid levels ect ect

the brakes have been re machined and new lining on the pads about 5000 ks ago

anything else i should do

i usually use gulf 1 - 10w60 synthetic oil in it

what spark plugs should i use?? any recommendations of which ones to use, or which ones to stay away from

what timing belt should i get i have seen those gates timing belts but maybe i should stick with the genuine nissan one seeing how critical a timing belt is and the fact that my engine is standard aswell, although gates belts are usually pretty high quality belts i think i would trust a geniune nissan one...

Thanks in advance

Rick

Link to comment
https://www.sau.com.au/forums/topic/272659-major-service/
Share on other sites

If youre planning on keeping the car for quite a long time, things I would do would be everything you have listed plus:

Get a hold of one of the just jap timing kits - they include gates belt (yes they are as good as nissan if not better), tensioner and idler bearings, cam and front main oil seals.

Have all of that fitted, and while youre at it, replace the water pump just for good measure..theyre only like $80 odd from nissan and 15mins to fit.

Off the top of my head i think the plugs you need are the BCPR6ES NGKs.

If they havent been done while you have owned the car, think about the gearbox, transfer, diff and ATESSA oils.

Once again if youre padantic, change the oxygen sensor as well. Expected life of those is about 100,000kms.

Link to comment
https://www.sau.com.au/forums/topic/272659-major-service/#findComment-4629051
Share on other sites

if you are in somewhere that gets snow, personally i would be going to a thinner oil. a 60 grade oil is a rather thick oil, especially when the rated oil by nissan is only about 30 i think (think it might be 7.5w30). so unless you have a lot of mods (which you don't) or the engine has done a lot of kms (which it hasn't) or has oil usage issues, i would get a thinner oil (it will also give you better fuel economy). for cold climates, especially if the car will be parked outside during the day at all and most definately if parked outside at night, i would suggest something with either a 0 or 5 cold viscosity and about a 40 or at most 50 hot viscosity. unless you really thrash the car a lot a 40w hot viscosity will be fine, since nissan only had a 30w oil as the standard recommended oil.

Link to comment
https://www.sau.com.au/forums/topic/272659-major-service/#findComment-4629099
Share on other sites

Gday Rick, i can highly recommend the 100K kits from KUDOS motorsport. My brother has a STAGEA and he put in a 100K kit last week, i am going to put one in my R33 soon too. Great value and super quick delivery too.

http://www.skylinesaustralia.com/forums/Ni...vi-t137554.html

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/272659-major-service/#findComment-4629201
Share on other sites

If youre planning on keeping the car for quite a long time, things I would do would be everything you have listed plus:

Get a hold of one of the just jap timing kits - they include gates belt (yes they are as good as nissan if not better), tensioner and idler bearings, cam and front main oil seals.

Have all of that fitted, and while youre at it, replace the water pump just for good measure..theyre only like $80 odd from nissan and 15mins to fit.

Off the top of my head i think the plugs you need are the BCPR6ES NGKs.

If they havent been done while you have owned the car, think about the gearbox, transfer, diff and ATESSA oils.

Once again if youre padantic, change the oxygen sensor as well. Expected life of those is about 100,000kms.

as above, but with Fuchs 10w30.

new wiper blades

radiator flush

new OEM thermostat

Link to comment
https://www.sau.com.au/forums/topic/272659-major-service/#findComment-4629257
Share on other sites

Gday Rick, i can highly recommend the 100K kits from KUDOS motorsport. My brother has a STAGEA and he put in a 100K kit last week, i am going to put one in my R33 soon too. Great value and super quick delivery too.

http://www.skylinesaustralia.com/forums/Ni...vi-t137554.html

Cheers.

kudos 100 000k service, are they all pretty much what u need for a 100 000ks?? and some upgrades as they listed.??

coz im thinking i might just get the whole kit from them instead of buying it one by one...

any advice in kudos 100 000 k service kit??

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/272659-major-service/#findComment-4634247
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...