Jump to content
SAU Community

R33 Gtr Air Flow Meters

CRAZD_GTR
 Share

Recommended Posts

CRAZD_GTR Explorer

CRAZD_GTR

Posted
Posted

hey guys have a r33 gtr with stock afms on it just had the car back from the mechanic wat we thought was the coilpacks or spark plugs were f**ked ended up being 1 of the afms one is doing wat it is ment 2 do while the other is doing its on little thing there for once on boost it goes into limp mod.

Now wat i heard is there is a possible tune u can do 2 them make them run right again just woundering if any1 has heard of this all has done this an if so how.

cheers in advance 4 ur help

Neil

Link to comment
https://www.sau.com.au/forums/topic/273733-r33-gtr-air-flow-meters/
Share on other sites
paulr33 Grand Master

paulr33

Posted
Posted

yeah not sure what you mean, you could try contact cleaner to clean the sensor if its covered with gunk

but if the actual sensor is shagged, then its dead, no point try to fix it

2nd hand GTR afm's shouldnt be that much, new ones on the other hand...

_Ryan_ Grand Master

_Ryan_

Posted
Posted
yeah not sure what you mean, you could try contact cleaner to clean the sensor if its covered with gunk

but if the actual sensor is shagged, then its dead, no point try to fix it

2nd hand GTR afm's shouldnt be that much, new ones on the other hand...

access autoworks list Z32's for 295 then 30each for tomei plugs... that with a power FC would cost the same as an autronic SMC, autronic might be cheaper!

R31Nismoid Grand Master

R31Nismoid

Posted
Posted
access autoworks list Z32's for 295 then 30each for tomei plugs... that with a power FC would cost the same as an autronic SMC, autronic might be cheaper!

and then you gotta make the piping fit

hence just buy Nismo's @ ~$900 delivered and be done with it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Manur33
      Rb25det coil loom wire identification

      By Manur33 · Posted

      Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • davemoto63
      Stagea choice's which model??

      By davemoto63 · Posted

      Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • davemoto63
      Noobie Stagea owner..

      By davemoto63 · Posted

      Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • CF.Panda
      R34 25GT Engine Light 21

      By CF.Panda · Posted

      I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...