Jump to content
SAU Community

Recommended Posts

hey having trubles with my rb25det s2

well when i first put engine in my car would drive good but there has always had a very little hisitation from round 5500 to 6500 but hardly noticable

has fmic, exhaust, only ever run 9psi

but then it started backfiring hard between 5-6.5g

i decided to wire up up an ignitor and wasted spark

has new vn coil and leads with 8 months old platniums

checked them and the white ceramic was cracked on one and you could c were it had been arc'n through so replaced with a spare irridium ( if anyone knows wot 45 dollar ones to put in)

know when it gets to round 4500 it just misses/pings, doesn't even rev past 5 easly

it seems to change behaviour(getting worse)

tried changing cas but no change

Link to comment
https://www.sau.com.au/forums/topic/273798-rb25det-power-troubles/
Share on other sites

Hold on what. THIS IS BAD

You put 2nd hand plugs in it and VN coils? like commodore coils wasted spark ignition? why?

NGK bkr6es is copper replacement plug for these things.

PUT THE STANDARD IGNITION SYSTEM BACK ON!

the standard ignition system is fine... when working properly.

check timing

doulble check boost

don't drive car till it pings this will cost you another engine.

try turning CAS all the way clockwise to minimize ignition timing before you drive anywhere

get your Air fuel ratio checked asap any 4wd dyno place will do it to confirm fuel issue.

a chipped plug would confirm major detonation event has occured, unless it was damaged on installation or removal.

hey having trubles with my rb25det s2

well when i first put engine in my car would drive good but there has always had a very little hisitation from round 5500 to 6500 but hardly noticable

has fmic, exhaust, only ever run 9psi

but then it started backfiring hard between 5-6.5g

i decided to wire up up an ignitor and wasted spark

has new vn coil and leads with 8 months old platniums

checked them and the white ceramic was cracked on one and you could c were it had been arc'n through so replaced with a spare irridium ( if anyone knows wot 45 dollar ones to put in)

know when it gets to round 4500 it just misses/pings, doesn't even rev past 5 easly

it seems to change behaviour(getting worse)

tried changing cas but no change

I'm not surprised you have power troubles with mixture of irridium and platinum plugs, ignitor and dunnydore coils and leads.

I think you need to replace all your parts with parts that fit the application that are strictly for the RB25DET NEO engine and then get it tuned.

If you cannot manage this then take it to competent mechanic who can help (most should be able to get you sorted.)

And make sure your base timing is set to 15 degrees on your CAS and plug gap is at factory 1.1mm as a start.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...