Jump to content
SAU Community

Recommended Posts

Dude,

Don't waste money on a dyno when its probably spark plugs ! When were they changed last ?

You want heat range 5 plugs, gapping them at 0.8 mm overcomes some missing problems

If its not Spark plugs I would go Coils, havn't tried the yellowjacket ones.

http://www.skylinesaustralia.com/forums/Mi...500-t32356.html

yes it sounds like either spark plug or coil pack issue. start with new plugs. if that doesn't help tape up the coils (there is a thread on here about how to do it). if that still doesn't work then it will more than likely be time for new coils.

i wouldn't go heat range 5 plugs. they are too hot and will just cause pinging due to higher cylinder temps. either BCPR6ES or BKR6ES are the 2 options. both will cost about the same and do the same job. ran both types in my 33

  • 1 month later...

I have seen it a couple of times on rb25det engines already. Like you gun it in 2nd gear, 4k, 5k, 6k and it like splutters. You think it should do the usual rev-limiter bounce, but it doesn't. It goes like brrr, like engine is running out of breath with very strange sound. Doesn't sound like the coil-pack misfire.

Anyone had this before ? When you rev it in neutral, nothing strange happens it just rev cuts at late 6k. Any ideas what could it be ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just had this happen to me too.  R32 GTR.   Also broke "just before going out onto the track" - someone up there is looking out for us... Very scary since I was about to do a narrow street course with zero run-off and curbs everywhere. Many people on here upgrading to billet uprights and R35 bearings?   Or buying new OEM knuckles?  I am not keen to replace with another s/h 30 year old fatigued part.
    • Top off with distilled water and see what happens. If you keep losing coolant then you know to start looking.
    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
×
×
  • Create New...