Jump to content
SAU Community

Clicking Sound From Wheels On Hard Turning

09GTR

By 09GTR,
in R35 GTR

 Share

Recommended Posts

09GTR Collaborator

09GTR

Posted
Posted

A friend of mine told me that at about 3000 kms his R35 started "clicking" loudly from the wheels on hard cornering. Well, on que, at almost exactly 3000 kms mine has started doing the exact same thing - and I havent even driven the car that hard. Sounds break-related. Does anyone else have this problem, or a remedy?

sickskyline Rookie

sickskyline

Posted
Posted
A friend of mine told me that at about 3000 kms his R35 started "clicking" loudly from the wheels on hard cornering. Well, on que, at almost exactly 3000 kms mine has started doing the exact same thing - and I havent even driven the car that hard. Sounds break-related. Does anyone else have this problem, or a remedy?

It sounds like the ball joints under pressure are you turning at full lock when this clicking sound happens. :(

09GTR Collaborator

09GTR

Posted
  • Author
Posted

Duncan, thanks for the link, it looks like they have it sussed out and are awaiting a fix for it. Also looks like a lot of GTRs have the problem. I'll take the info you sent me to Crawfords.

Cheers.

Gibbo_R35 Community Regular

Gibbo_R35

Posted
Posted (edited)

I had exactly the same noise when turning right at higher speeds, a couple of runs through Galston Gorge revealed this. The strange thing though is that the noise is now gone, I do not know what has changed.

On a side note just for readers information, there is a rattle noise from the front of the car when I go over a bump, this combined with with clicking when turning raised some flags. Anyhow after some inspections I found the issue for the rattle when going over the bumps, the top steel pin that goes through the caliper is a floating pin and vibrates and rattles.

I am curious who else has seen this.

Cheers

post-57732-1244937324_thumb.png

Edited by Gibbo_R35
09GTR Collaborator

09GTR

Posted
  • Author
Posted
I had exactly the same noise when turning right at higher speeds, a couple of runs through Galston Gorge revealed this. The strange thing though is that the noise is now gone, I do not know what has changed.

On a side note just for readers information, there is a rattle noise from the front of the car when I go over a bump, this combined with with clicking when turning raised some flags. Anyhow after some inspections I found the issue for the rattle when going over the bumps, the top steel pin that goes through the caliper is a floating pin and vibrates and rattles.

I am curious who else has seen this.

Cheers

Thanks Gibbo, interestingly the noise has not reappeared today on my car either. I havent had the rattle noise.

  • 7 months later...
LSX-438 Mentor

LSX-438

Posted
Posted

I've had this clicking noise surface recently.

It seems the USA boys thinks it is one of these:

1. Missing top pad retaining SPRING (the front calipers usually only have one of these)

2. Rattling pad retaining PIN (as mentioned above)

3. Loose tie rod ends

Did you guys resolve this and/or had it resurface?

fungoolie Community Regular

fungoolie

Posted
Posted

I'll add another one to this. I had the problem appear at around 9000 kms and took it in to Nissan. They said they spoke to Japan and diagnosed it as the fully floating rotor making noise because some anti-seize grease they use between it and the hub had washed out. Anyway they replaced it with a non genuine compound as they didn't have the proper stuff in stock and it lasted a week before the noise reappeared. I'm now on 17,000 kms and about to take it back in as I want that looked at as well as my MFD backlight dying on hot days as well as my interior mirror developing a droop on 40+ days after a day in the sun. I'll see if I have that retaining clip installed tonight and suggest that to them as well the tie rod end when I drop it off this week.

I've had this clicking noise surface recently.

It seems the USA boys thinks it is one of these:

1. Missing top pad retaining SPRING (the front calipers usually only have one of these)

2. Rattling pad retaining PIN (as mentioned above)

3. Loose tie rod ends

Did you guys resolve this and/or had it resurface?

fungoolie Community Regular

fungoolie

Posted
Posted

No top pin anti rattle spring found and that upper pin clicks loudly with a similar sound when I push it side to side. To me it seems the obvious fault/problem. See what Nissan thinks...

LSX-438 Mentor

LSX-438

Posted
Posted

Out of interest i put the car up on stands today, and started t up, put it in gear, bit of throttle, turned full lock (left) and no clicking. So when there is no load on the wheels/suspension i dont get the clicking. Might be a clue... anyway i am going to be taking a closer look over the next few days, just ran out of time today.

fungoolie Community Regular

fungoolie

Posted
Posted
I'm no R35 mechanic (just a normal mechanic anyway :down: ) but a click on full lock is normally worn out CV joints. Has anyone actually got to the bottom of this problem yet?

Yes I can see how you would think that, that was my first suspicion as well but the Nissan Tech had a listen and said it definitely didn't sound like CVs. Plus a fiddle with the brakes and it gets better immediately, albeit temporarily in my case. In fact last night by just playing with the pins and moving them back and forth stopped the problem for about the first 20 mins of this morning's drive before they must've shifted again to their favourite rattling position! The sound from the pin when manually rattled does sound a lot like the click you hear whilst driving and the US guys seem to be convinced that the anti rattle spring omission seems to be the problem..

Kujotk Grand Master

Kujotk

Posted
Posted

i havent read all the posts or the links, but ive had cars with similar issues (NOT R35) and with these cars its either a Faulty brake assembly (uneven ware on one pad), CV joints or a worn/broken wheel bearing..... ive eevn had a car with diff probs making a similar sound but for the rear of the car, and even the power steering...

LSX-438 Mentor

LSX-438

Posted
Posted (edited)

Like i was saying i was getting the clicking, just turning left. Put the car up on stands and with no load on the wheel, and with wheel turning...no ticking. Anyway i had to replace the pads anyway... So i did remove the pad pins and re-install again. Also the tie rod end nut was not very tight, i could tighten a couple of turns. After i did all this and put it all back together the noise was gone! So unfortunately i can't isolate where the noise was coming from exactly. It's either the tie rod or something related to the caliper. It doesnt look like a stuffed CV. Interestingly also, i noticed the tie rod end cotter pin can rattle around, when you move it with your finger it sounds a hell of a lot like the noise in question.... tick tick tick... so i tapped it down tighter. Anyway the noise is totally gone for now i will let you know if it comes back. Relieved it's not a CV.

Edited by LSX-438
fungoolie Community Regular

fungoolie

Posted
Posted

Was informed by Main North Nissan today that they have three owners with the clicking problem at the moment and are narrowing down the cause on a test mule. So they told me to hold off bringing in mine till they sort it out. I told them about the info available on the US forums regarding missing top anti rattle springs and loose tie rod ends and it appeared to be news to them! We'll see if they can come up with a permanent fix soon.

roadworia Collaborator

roadworia

Posted
Posted

we get a lot of nissans with similar noises. found that the cv shaft spline is dry causing the clickling. i removed cv, lubed spline and retorque the hub nut properly and noise goes away...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Duncan
      After market rear camber arm adjustment

      By Duncan · Posted

      Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • V35Newbie
      After market rear camber arm adjustment

      By V35Newbie · Posted

      I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
×
×
  • Create New...