Jump to content
SAU Community

Recommended Posts

Picked my car up from ben at racepace yesterday after getting a tune done. Took it for a drive tonight and twice under load at mid-high rpm the car sounded like it was missing (didn't sound like detonation.) Had a look at my power fc and the first time the knock was at 34 and second time 46. Are they dangerously high levels? :(

Link to comment
https://www.sau.com.au/forums/topic/274573-knock-question/
Share on other sites

Im surprised, usually with the stock default map they detonate out of th ebox. I wouldnt lean on it too hard without a tune. Remember a stock setup detonating can crack a piston easier than a 350rwkw well tuned setup.

im suprised too, it runs so much smoother than the stock computer just plugging it straight in.

i dont want to spend 500+ on a tune, then in 2 months time upgrade the turbo etc which im planning to do and then have to spend the same again to get it tuned again

Link to comment
https://www.sau.com.au/forums/topic/274573-knock-question/#findComment-4655551
Share on other sites

im suprised too, it runs so much smoother than the stock computer just plugging it straight in.

i dont want to spend 500+ on a tune, then in 2 months time upgrade the turbo etc which im planning to do and then have to spend the same again to get it tuned again

I read an article on stock pfc maps for an s15 and they were very aggressive; i would assume that would be the same for most jdm imports too. You would feel more power but its probably running lean, a little too lean.

in regards to knock, I see 14 on cold nights at higher throttle but can see 34 or so on a hot day.........want to add, was cruising on a rough road at 80km/h, pushed the clutch in and let the car coast while i reset the handcontroller and monitored the knocks and it still registered about 25 so it would be plausible to assume that roadnoise can influence knock to some degree.

Link to comment
https://www.sau.com.au/forums/topic/274573-knock-question/#findComment-4656149
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...