Jump to content
SAU Community

Recommended Posts

I think you would be more than lucky if there isnt ceramic dust inside the motor...

But anyway, you cant really tell @ idle. Obviously power/boost wont be the same... thats a given, but then why even attempt that and almost gaurantee a dead motor.

Just pull the dump off

well you have two turbos too worry about. but if it's stock then that seems reasonable. what give you the incline that they were damaged or were you just asking for future reference?

when it happens you will know about it. if you have the cash get some steel wheels put in there or upgrade. my 2c.

Symptoms are: no ability to make boost, and crappy running if you run the motor under the conditions in which it would have made boost. The working turbo will just push air backwards through the broken turbo's compressor, therefore no boost at the plenum. Idle and low throttle are fine as you are in vacuum.

just put some steal wheel turbos on a mates gtr he was on his way to adelaide and was all fine then went to over take a car and no boost, there was no bang clunk or anything just fell off. replaced turbos and checked comp and all good.

so they can let go at anytime you dont need to be giving it a hard time at all. we also never found the wheel thanks to a decat pipe.

From what i have gathered you dont have to be boosting hard thus creating massive heat and spinning the turbos at 1000000rpm for them to let go.

I guess with age, the more shaft play u get, if the exh wheel only scrapes or bites the housing this would be enough to send it flying out the back!?! That's why it's more common with the r32?!?

Its predominately heat, heat generated by shaft speed IMO.

Which is too much boost in the given application in simple terms.

eg. You are probably OK with 13-14psi for usual street duties

Circuit you wouldnt run anymore than 11-12psi... being extended laps is going to get a lot more heat in there

Hence its usually the rear turbo that lets go - hottest cyclinders are 5/6 in a stocker style setup.

Hence its usually the rear turbo that lets go - hottest cyclinders are 5/6 in a stocker style setup.

Why do 5/6 get hotter? Is that why ppl richen up 6? Or does 6 run a little leaner than the others so its just compensating?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...