Jump to content
SAU Community

Recommended Posts

:P ty its actually measured off my R33 interior.

well. it only took a few arvos to weld up. could use some refineing and was relatively cheap.....the only catch is the seat. I had it lying around and its an actual car recliner, so it weighs as much as the rest of it combined. a generic seat of a lighter cheaper description would make it much more affordable.

Edited by boiracer
dude.. srsly??

what do you think polyphony have been doing for the last 5 years??

my money is that you'll forget all about forza before long..

working on other games.. As they stated in their interview.. Prologue and PSP GT and a couple of others.. You didnt think they been spending the last 5 years only working on this game?

well there is a light at the end of the tunnel. the game is currently in production.

there was some funny responses to this on GTPlanet. this was my favourite.

FOX NEWS BANNER APPEARS

This just in, a truck carrying all the Gran Turismo 5 discs has been loaded onto a plane to Yemen, along with a printer, a man wearing baggy underwear, and a guy wearing a shoe with a match.

yeah i been waiting for them to put a r33 gts-t in it too. do they have the r32 gts-t in the earlier ones? from memory they do. sif put that gutless piece of aids in and not the 33

I'm not sure. I haven't played GT since GT2, have been playing Forza.

In Forza 3 I had to convert a R33 GTR to RWD to make it like a GTST but it still keeps the RB26 so it's not a real GTST of course.

yeah i been waiting for them to put a r33 gts-t in it too. do they have the r32 gts-t in the earlier ones? from memory they do. sif put that gutless piece of aids in and not the 33

in gt4 you could get an r32 gts-t m spec, though if i remember you could only get the r33 gts and not the gts-t.

i will be pretty sad if theres no r33 gts-t. but you would think after taking 20 light years to make they would have all the nissan skyline's down pat. same goes for the 180sx.

Anyone know for sure if the R33 GTST is back in or not?

I'm tired of pulling out GT2 and the OLD Playstaion to relive my old car :)

I suppose we'll find out in about a months time.

pft, your doing it like a sucker

forza 3 has all the cars....

pretty sure one of the guys at harvey norman here has one. needless to say he works in the computer section. and he drives a supra, which isn't suprising since a hell of a lot of IT nerds drive imports. pretty much never see one in a commodore. it's usually either lancers or imports.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...