Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

This is my Pedders experience.

Had the wheel alignment done on my R33GTS-T and it came back with a large scratch in the left rear quarter panel - which they obviously denied doing. Had a great fight with them when I asked them to use Gary's (Sydneykid) settings for the wheel alignment - they did it but with much complaining and probably resulted in the scratch.

Prices are very expensive - 12mm camber bolts Pedders = $115, Whiteline $79

The only thing going for them is that they stock front ball joints for R32/R33/R34 GTS-T's.

Link to comment
https://www.sau.com.au/forums/topic/274952-pedders/page/3/#findComment-4826267
Share on other sites

so they measured up my car to see how much lower it will be with there sports ryder springs. (i have nismo s type struts and an unknown but firm spring, that i figured was stockish height)

aparently they will raise the car 10mm both ends. wtf type of lowering spring is that!!!

*starts saving for coilovers* (not pedders)

Link to comment
https://www.sau.com.au/forums/topic/274952-pedders/page/3/#findComment-4826489
Share on other sites

meh pedders here don't even stock more than about 4 parts for R32 GT-R/4 suspension and the guy took a look at my car and says 'hmm haven't seen many of those', would rather get stuff done at goodyear - at least the guys there had a good idea of how an R32's suspension works!

Link to comment
https://www.sau.com.au/forums/topic/274952-pedders/page/3/#findComment-4826585
Share on other sites

  • 2 weeks later...
  • 11 months later...

Hi all, first time poster and owner of a skyline R34. went to get it looked at by a local mechanic coz the steering wheel was vibrating a bit on idle. He said I needed to get the front radius rod bushes replaced and suggested I go to pedders coz it's an import.

So I go to pedders and got them replaced for $260 but then they told me that they couldnt do the wheel alignment coz the steering gear is leaking internally and will cost another $1100 odd dollars to fix.

Just wanted to know if this sounded reasonable and should I be looking around elsewhere to see if it is bull. Can anyone recommend someone in melbourne, particularly in the western suburbs?

Link to comment
https://www.sau.com.au/forums/topic/274952-pedders/page/3/#findComment-5428632
Share on other sites

So I go to pedders and got them replaced for $260 but then they told me that they couldnt do the wheel alignment coz the steering gear is leaking internally and will cost another $1100 odd dollars to fix.

Just wanted to know if this sounded reasonable and should I be looking around elsewhere to see if it is bull. Can anyone recommend someone in melbourne, particularly in the western suburbs?

No it's not reasonable. A second hand steering rack should only be 300 or so, and it isn't that much in labour to install. Also, I can't see how a leak would prevent them from doing a wheel alignment. Just go somewhere else to get the alignment done.

Link to comment
https://www.sau.com.au/forums/topic/274952-pedders/page/3/#findComment-5431439
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • No. BSP lost to the cultural/technical imperialism of living next to Trumpistan. Face it, Robertson screws were better and still pretty much lost out to the yank stuff. The Europeans hate the Brits and they don't use NPT. NPT is just as "imperial" as BSP is, being based on those useless inch thingos. Just done differently. 
    • I live in Quebec. Our license plate slogan is "Je me souviens" Translated is "We will remember" as a reminder to when England conquered us and that we must never forget what they did. Long story short, BSP is unheard of here due to being an English design. I'm surprised our nazi anti english government office the OQLF hasn't kicked in my door yet just talking about it, yet alone imperial anything.       
    • Thanks for that! I did a quick Google search looked up some of hydaulic stores and didn't see it listed on the website, I'll give them a ring. Also found out later that I can buy 2 oem bleeder bolts for 10 bux and come with the washer which I might do so I don't waste the money it costs in petrol to find 2 washers (already did that lol). The old copper washes look in good nick, I drove it after taking it off and putting it back on and didn't see any  Part number here for reference if anyone needs: 14053-42L0A  
    • Piggaz had one and broke it at 470kw 
×
×
  • Create New...