Jump to content
SAU Community

Recommended Posts

Hi, ive got an r34 GTT and i wanted to get a respray. Its like a Ferrari red and i really like the colour but its getting a bit faded so i wanted to get it touched up. I dont really care about getting the engine or anything painted i just want the outside done. I was hoping someone would know roughly how much it costs, i thought it might be a bit cheaper considering i want the same colour done or as close to as possible, but ultimately i jsut want it too look nice and new again. I live in Adelaide so if anyone knows of the some places here and roughly prices itd be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/275171-respray-on-my-34/
Share on other sites

yer i have, it worked a bit but i think the paints a bit too far gone. It still looks alright, but i want that new car shine lol. I did do the polish myself with a friend so it wasnt professional, but we did a good job and my mates done it few times so i think we did all right. i used good products too. Does it make much of difference if you get it professionally done, i wasnt sure if itd just be a waste of money.

5-7k would be for a full respray all round.

If your just looking to get a exterior respray in the same colour it would be between 2-3k depending if u take the bars off yourself etc.

Cutting back their labour will save u hundreds.

I have the same colour and have the same problem haha.. but im in sydney so i cant help u there man.. Best idea would be to ask in the SA section of the forums for a good shop.. then take your car around and get a quote.. tell them u can take the bars off and put them back on (only if u know how to, its piss easy)

But remember some places are cheaper because they do a shabby job, be confident in who u get to do it and if its not good enough (look thouroughly) dont pay till its fixed, its worked for me before..

there was a pretty popular spray painter in Syd who does exterior respray for $1.5k ..forgot the name but if you search for 'respray' it should be in one of this year's threads. But yeah doesn't help you much if you're in Adelaide .. but still, $5-7k ? LOL. Seriously people, they're not ferraris.

For the same color, it would cost you $4 k but if you need the add the metallic would be + $2k on top.

Unfortunately, this is the quote from Syd. All prices I said is about respray outside only.

Hope it might give you some idea.

You can have it shipped to Japan and sprayed in the original Nissan factory for $7k.

I've had my old car smash repaired from a major rearend collision and resprayed for less than $7k and that's including a lot of genuine panels etc.

that smashtech place would be wicked if it was in adelaide, does anyone know of anywhere similar here, or even if it cost 2 k it would be sweet, i just dont really know of any places to go to in adelaide.

some weird stuff in this thread

no, you can't send your car back to japan and get it sprayed all for $7k, i may have missed the joke on this. Plus the Japanese are NOT known for the panel beating prowess...

yes you can get cheap resprays, cheap 99.9% = crap.

$5-7k is probably the MINIMUM a good rep place would charge for nice, relatively flat finish.

$7k i would say is a top quality panel beater, with a result you won't have to worry at all about.

There are SOME places around that can do good jobs for around $2-3K (DT Panels in melbourne for example), but they are few and far between. Try and find a workshop that deals mainly in imports.

Please detailed your polishing process. Was it by hand or machine? What are these "good" products? If machine, what machine, what pads and what polishes

Take some pics... i'm leaning towards a pro detail to solve your problems, and i'll post some pics to why i think this a little later.

Once you learn a little about painting and what's involved, you very quickly understand why some jobs cost $2k and why some cost $10k.

car master paint and panel look it up on google for numbers etc... hes a bit of a backyarder but does a really good job for the price. If you dont want your car in any car shows as a trailer queen, and want it as a daily that looks nice than hes your man.

call up tafe and ask for pannel beaters course, they will generally do your car if you supply paint etc for around 1k. but they will keep it for a while as they will be using it to train young pannelbeaters. The job however is mint as.

my mates uncle had his dodge charger done by tafeSA and it was all quality.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
    • To drain the Intake Heat Exchanger, there is a crappy drain plug in front of the driver's side front tyre: You should use the largest headed phillips screwdriver you had, and in my case I needed vice grips on the hose above as the plug was tight (tighter than it needed to be, since it has an o-ring seal).  After you have a tray down and open the drain, open the intake heat exchanger reservoir cap (drivers side one) and you should get a couple of litres of coolant To get to the radiator, you need to remove the plastic engine undertray. It is held on with a series of 10mm headed bolts and some clips. For the radiator, there is another type of crappy drain (kind of like a plastic banjo bolt) and you should attach a length of hose to direct the stream of coolant per this pic (otherwise the coolant hits the rad support and goes everywhere). The drain is on the rear of the radiator on the driver's side and a bit hard to find. Put a big tray or bucket down (5l won't be enough) and slowly unscrew the fitting by hand. You only want to remove it far enough for coolant to flow, it you unscrew it right out the whole fitting and direction pipe will come off and you will get a coolant bath (yum!). Undo the radiator reservoir cap and it should empty about 8l
    • So, this shouldn't be such a mission, but there were a few tricks so I thought I'd post up a DIY for it. This was on a Q50 Red Sport but I doubt any other V37 model is very different (maybe just less steps for the intake heat exchanger hoses) I pulled the radiator out to flush it because the car was running hot at the track, but obviously the same steps apply for changing a radiator for any reason including an upgrade. If you are removing the radiator, you of course need to drain and refill, so have 5+ litres of blue coolant ready. You also need to drain the intake heat exchanger to remove the radiator so you will need a couple of litres for that as well. You will also need something to deal with the auto transmission lines, I used 2x 8mm rubber caps on the radiator side, and a short length of 8mm pipe on the car side.....unless you can block these lines quickly you will loose AT fluid and it may be enough to hurt the transmission if you don't refill it. 2 other tools that really help dealing with coolant lines and spring clamps are Bent Needle Nose pliers Hose pliers Between them they will reduce the frustration (and injury) potential by about 1000% Other than that....lets go... "First, jack up your car". Yes really, and put it safely on stands. If you are not confident doing that you need to give this job to a mechanic
    • If the forester is anything like our old 2007 GTB Liberty, I could near on run ling Long's and "rate them", as no matter what, it just hung to the road, even when abusing it in a hard launch in the wet, or throwing it at corners.
×
×
  • Create New...