Jump to content
SAU Community

Recommended Posts

hey guys

well a little while ago my speedo just stopped working . so i searched on the forums and found something about the speedo cable snapping hence why hicas light turns on and i lose power steering after a couple minutes of driving.

today i changed the speedo cable over and nothing was wrong with the old one . so if anyone has any idea's on what could be wrong any help would be appreciated

thanks rory :)

Link to comment
https://www.sau.com.au/forums/topic/275218-no-speedo/
Share on other sites

was the apexi rsm installed recently?

check the speedo wiring near the ecu, maybe that has a short somewhere there.

i know when i installed my rsm. i forgot to tape up the speedo wire. so when i turn corners the ecu would move, making the wire ground itself to the body and the steering would go heavy.

Link to comment
https://www.sau.com.au/forums/topic/275218-no-speedo/#findComment-4663551
Share on other sites

was the apexi rsm installed recently?

check the speedo wiring near the ecu, maybe that has a short somewhere there.

i know when i installed my rsm. i forgot to tape up the speedo wire. so when i turn corners the ecu would move, making the wire ground itself to the body and the steering would go heavy.

32's use a cable driven speedo, and i think the ecu gets a electronic signal off the back of the speedo.. so if the RSM was shorting out, it shouldn't stop the speedo from working.

Link to comment
https://www.sau.com.au/forums/topic/275218-no-speedo/#findComment-4665251
Share on other sites

hey guys

well a little while ago my speedo just stopped working . so i searched on the forums and found something about the speedo cable snapping hence why hicas light turns on and i lose power steering after a couple minutes of driving.

today i changed the speedo cable over and nothing was wrong with the old one . so if anyone has any idea's on what could be wrong any help would be appreciated

thanks rory :D

Well, you will be happy to know that I am experiencing the EXACT same problem, Hicas light, no Power steering, No Speedo.

Im not sure what ties them all together but this is the second day this has happened, Im at work at the moment but im going to try to see if the speedo works up untill I get the hicas light on.

Link to comment
https://www.sau.com.au/forums/topic/275218-no-speedo/#findComment-4665616
Share on other sites

Well, you will be happy to know that I am experiencing the EXACT same problem, Hicas light, no Power steering, No Speedo.

Im not sure what ties them all together but this is the second day this has happened, Im at work at the moment but im going to try to see if the speedo works up untill I get the hicas light on.

hicas and power steering are speed sensitive, so no speedo reading gives you hicas errors and heavy steering.

Link to comment
https://www.sau.com.au/forums/topic/275218-no-speedo/#findComment-4665629
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
    • the top black section is bonded to the silver section with some form of rubber. I assume to isolated NVH from the box
×
×
  • Create New...