Jump to content
SAU Community

Recommended Posts

I have recaros in my stagea which were R33 GTR skyline. I know because the recaro boxes actually had 33gtr skyline stamped on.

Im short and whilst they are lower I have no problem in seeing over the bonnett. might be different with stock GTR seat but I would have thought they will be fine

30062007016.jpg

DSCF8875.jpg

I'm soon to have a set in my car, Darrin. They're from an R32 and are being re-upholstered at the moment.

Either way, I have the factory seats set to the lowest setting now, and I'm around 5'10" tall.

I have R33GTR seats in mine and I'm 5'10

You do sit lower, but its a comfortable low, and no problems seeing over the dash at all.

Thanks for the reply's. I use to have Garage Impul seats seats in mine with skyline rails and they were lower approx 30-40mm than stock seats. I am 5' 10" as well

I have a spare set of stagea Bride rails, so tosing up between using them with new bride seats, either Euro II or Digo graduation cloth and retrimming the rears and doors to suit, or I also have a spare series 2 manual rear seat and door trims which are almost identical to R33 GTR cloth. Using GTR seats will be alot cheaper option, but the Brides will look good :D

Was also looking at buying s/hand recaro's and retrimming them, but the trimmer wants aprrox $1000 just for the fronts. Might as well buy new ones.

Nick, what is it costing to get the gtr seats done? What sort of cloth?

I also have a spare series 2 manual rear seat and door trims which are almost identical to R33 GTR cloth. Using GTR seats will be alot cheaper option

That's pretty much what I did with mine.

Here's a pic so you can see how the seats and trim go nicely together.

post-44730-1245391351_thumb.jpg

I have 33GTR seats in the 32, if i keep the stagea they might go into it and buckets in the 32, or more gtr seats, they are sooooooooo comfy. stagea ones i dont find supportive enough in the lower back, so the harder GTR seats are great. i am 6'2", and my shoulders are getting on the high side for the GTR seats though.

Was also looking at buying s/hand recaro's and retrimming them, but the trimmer wants aprrox $1000 just for the fronts. Might as well buy new ones.

Nick, what is it costing to get the gtr seats done? What sort of cloth?

The rough quote so far is $1400 for all cloth, or $2400 for all leather, so I'm guessing that the final cost will be somewhere in the middle, as I'm going half-and-half. That, though, is for the whole interior: front and rear seats plus door trims. I picked the colours and materials the other night, so it's not too far off, hopefully.

I've got the R32 GT-R rear seats still, so I really should advertise that, and after the rest is sorted, I'll have a pair of Stagea front seats to get rid of too.

I want to know HOW much lower do you sit with GTR seats

Hard to see over the bonnet?

Hi Darrin,i don`t have GTR seat`s but 32GTST seat`s & you sit some 90 mm lower & it`s a lot different looking over Bonnet but it`s so much more comfortable as you now feel apart of the car instead of sitting on the Couch,post-36964-1245453736_thumb.jpgpost-36964-1245453822_thumb.jpg

cheer`s chuckie.

  • 2 weeks later...

What rails are you blokes using?

Pretty intererested in swapping my seats for ones that acutally hold you in. Are you able to use your existing rails to suit GTR seats?

Edit: After using the search function, I found the answer I was looking for :rofl:

Edited by d1_drifter

Hmmm, I already have the standard Stagea seats set at the lowest point at the back and a little bit higher at the front to provide some under-thigh support, so I wonder what the new seats will be like.

I (finally) got my recaros fitted the other day: it took custom sandwich plates between the seats and the Bride rails: perfect seating height: maybe 10cm lower than standard: very happy: haven't even bothered with a quote on full retrim yet: I am waiting to get my manual console first...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...