Jump to content
SAU Community

Recommended Posts

Hi i have a strange hicas problem.

Car is 1993 R33 Sedan Auto RB25DET

The HICAS usually light on every second start of the day.

Which means everyday when I first start my car, it is fine.

Till I reach somewhere and turn off the ignition, after a while turn on again, the HICAS light will comes on.

So it is like, for a non-cold start, the hicas will light on.

Everything is fine, all fuses are checked (under driver's side and rear boot).

Mechanic asked me to seek help from a power steering specialist.

What do you guys think?

I tried to run the HICAS diagnostic but it never success, tried a couple times and the engine check light never flash.

I wonder is there anyway to diagnosis the HICAS?

has anyone encounter this before?

also does HICAS affect fuel consumption? cause I have been having 16L/100kms for a very stock car.

should I remove the HICAS with a lock bar for daily driving (normal drive)?

car had just recently been major serviced.

Link to comment
https://www.sau.com.au/forums/topic/276622-hicas-problem/
Share on other sites

Hicas Problem:

HICAS Solenoid R.H.

HICAS Solenoid L.H.

Fail-Safe Valve

Vehicle SPeed Sensor

Steering Angle Sensor

Steering Neutral Position Sensor

Parking Brake Sensor

Inhibitor Sensor

among these i think only fail-safe valve and inhibitor sensor is related to car temperature?

when the coolant temperature is low and if the car is ignited there will be no HICAS

it's just when it is non-cold start then HICAS will turn on

what is fail-safe valve (where is it?)

and inhibitor sensor

could someone explain?

cheers

Link to comment
https://www.sau.com.au/forums/topic/276622-hicas-problem/#findComment-4682915
Share on other sites

easy solution is to just get a hicas lock bar and remove the worry all together. Remove the hicas light out of the dash and regularly check your power steering fluid to make sure its topped up.

I read somewhere a very long time ago, and I dont know if this applies to the newer models of HICAS where they dont use the powersteering fluid to work, but apparently if there is an Air bubble in the lines (or if it wasnt bled properly) that could possibly trigger the warning light. In saying that, try bleeding the powersteering fluid properly and see how you go.

Link to comment
https://www.sau.com.au/forums/topic/276622-hicas-problem/#findComment-4685554
Share on other sites

easy solution is to just get a hicas lock bar and remove the worry all together. Remove the hicas light out of the dash and regularly check your power steering fluid to make sure its topped up.

I read somewhere a very long time ago, and I dont know if this applies to the newer models of HICAS where they dont use the powersteering fluid to work, but apparently if there is an Air bubble in the lines (or if it wasnt bled properly) that could possibly trigger the warning light. In saying that, try bleeding the powersteering fluid properly and see how you go.

yea I am thinking to remove the HICAS with the lock bar but people around me suggest me to find out the problem before removing it because it indicates a problem

my power steering fluid has been changed lately after a major service tho

Link to comment
https://www.sau.com.au/forums/topic/276622-hicas-problem/#findComment-4685559
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...