Jump to content
SAU Community

Recommended Posts

Hey Guys/Gals,

OK.... I have about 10 rooms booked for us at the Tudor Motor Inn.

All bookings are coming through me this time, so let me know how many people etc and I will allocate you a room.

Once the Tudor is full, people will need to call across the road to book a room.

We will be staying - Fri 14 and Sat 15 August

Details are:

Tudor Motor Inn - 5821-8411

64 - 66 Wyndham Street, Shepparton (left hand side heading out of Shepp towards DECA)

Twins - 1 queen OR 1 queen & 1 single - $93.50

OR

Family Rooms from $121

There is offstreet parking.

As of this morning, there was also still rooms available across the road at the: (prices may have changed)

Courtyard Motel - 5831-2355

Standard twins or single - $98

Deluxe twin or singles from $109 (spa included in rooms)

Standard triples - $108.90

OR

Best Western Windermere Hotel - 5821-3088

Singles - $110 / night

Doubles / Twin - $125 /night

Triple - $135 / night (1 queen, 2 singles) - quad = $145

PS. If youre looking for a friend to share a room with, post your interest here - im sure there will be others in the same boat and im going to try and squeeze as many of us in at the Tudor as I can.

Cheers

B

Dinner is booked at 7pm @ Taco Bills.

Staying:

Fri/Sat

Bec and Ryan

Crossy and Jarrod

Mick and Tim

Tony & Tom

Brendan + Cass

Brendans friends

Brendans friends

Juliette & Liz

Shane J + 1

Russell, Tim, Campbell etc...

Keiran + 1

Che and Russell

Ryan Campbell + GF

Daniel Hall + GF

Cassandra

Fri only

Al

Pat and friend

Sat only

ActionDan

Leon + 1

Russell's friends x 8

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Bec can I put my hand up for a Twin to be confirmed after this weekend when I see if my car survives the track day?

I'd say BrendanR33 would want a Twin also.

Edited by ActionDan

Dan you are correct.

Bec I would like to reserve 1 Twin Room for myself and Cassie, and if I could please reserve 1 Twin room for my mate and his girlfriend. He is trying to get his car ready for the event, but either way he will be coming along (for fishbowls).

Thank you,

Brendan.

One more thing, I am guessing that the $93.50 is per night?

whats the deal with a family room? is that a queen/double and two singles? for 121?

Roman, you and pete interested in splitting with kate and I?

And a twin room with the queen and single for 93, is that all in one room or in two?

trying to work out the cheapest way to do this :blink:

My mate and myself will be heading up, looking for the easiest/cheapest place to stay for both nights.

So if anyone wants to squeeze us into their family room we're happy to take the two single beds, otherwise we'll probably just book a room with two singles.

Cheers.

Details are:

Tudor Motor Inn - 5821-8411

64 - 66 Wyndham Street, Shepparton (left hand side heading out of Shepp towards DECA)

Twins - 1 queen & 1 single - $93.50

Family Rooms from $121 <----- queen/double and two singles???

and out of any of the places listed, are any of them that have a queen and a single, or a queen and two singles, and the singles in a seperate room?

Edited by RB_Ryan

Ahhhhh - well that changes things.

The rooms I have booked are for Friday and Saturday - its a package deal at the moment, both nights or no sale.

Although I might know someone who just wants a bed on Friday night - lets chat on FB and we'll work it out.

Hey Bec.

Can you please book me a room for 4. Possibly 5. How many beds in the family room?

Its for me, tim, campbell and dean. Maybe mat.

thanks.

Hopefully no south australians next door :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...