Jump to content
SAU Community

2.8 Hks Stroker Bottom End

555kkk
 Share

Recommended Posts

grygtr Collaborator

grygtr

Posted
Posted

What the photo doesnt show is that the s-pipe is useless without the second part i thought i was getting. he then "found" the second part and offered to send me that,Much like he sold me the plenum then called and said Oh I "found" you will need the S-pipe

The guy Bull#$%ed about having sent the S-pipe several times to me I missed my dyno booking. When it did arrive poorly packed(in an envolope) and in bad condition, i discovered it was useless to me.I would not spend 8.5k with someone who has show himeself to lack any sense fairness in a a $250 transaction.

You will probally find you wont get your rings or pins or something like that, maybe he will "find" a 6th piston after sold you 5.

555kkk Experienced

555kkk

Posted
  • Author
Posted

I sent you exactly what was advertised and in the photograph ! if your mechanic didnt know how to fit them it time for your dyno run not my problem . you got exactly what was advertised.

Sold $5000 dollar set of endless brakes to adam on here last week he was more then happy with my photos and description. sold $1600 tomei head, apexi rx 6 turbo $1500, another Modified head $1500, sequential 6 speed trust box $10,000 NO complaints ! i could have sold the part to other people at the time, but you said "no you had already put money into my account" you were that certain about part you didnt even say ill take it - you just put the money into my account.

555kkk Experienced

555kkk

Posted
  • Author
Posted (edited)

just got brand new HKS individual prices for pistons rods and crank

pistons 3340

rods 3870

crank 9239

so if i was to split into the three parts the amounts stated earlier for individual parts would change. my mistake sorry

Edited by 555kkk

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
×
×
  • Create New...