Jump to content
SAU Community

M35 Ecu Remap

Bis-e Bee
 Share

Recommended Posts

Bis-e Bee Mentor

Bis-e Bee

Posted
  • Author
Posted

Ok doods, the spare ECU has been tested and appears to operate to requirement, I wanted to ensure this was the case prior to dropping everything off to SAS and finding out the spare was dodgy or damaged in some way.

Another thanks to Ken at Prestige Motorsport, what a legend :)

I took some photo's of the equipment behind the glovebox and kick panel for those who havn't had a look yet, note however that when you remove the glovebox don't forget the screw on the bottom left hand side. You need to remove the left kick panel, just insert a screwdriver and lever it off, it's got two clips that lock in and just a plastic nut holding the back end on. I'm not sure if I did it or if it had been done previously but the bottom left hand corner of my glovebox is now cracked, will have to fix it with some glue when the glovebox comes out next for it's trip to SAS. I kind of didn't find the concealed left hand bottom corner screw until I had done all the other one's and had begun gently trying to lever the glovebox out. Thought I would warn other's incase they can save this damage to the glovebox.

Anyway, I'll chuck the pictures up for anyone who is interested. I also emailed SAS yesterday and have brought up the topic of the possibility of a switchable dual mapping, this probably can't be explored until the car goes in but I will be sure to pursue the matter.

Thanks to Iain for his phone support in getting the glovebox out and the ecu unplugged etc. I owe you another double shot macchiato.

post-59561-1250381948_thumb.jpg

post-59561-1250381971_thumb.jpg

post-59561-1250382048_thumb.jpg

Bis-e Bee Mentor

Bis-e Bee

Posted
  • Author
Posted
:thumbsup:

I suspect you can only have one or the other

I have emailed Tom at SAS, I havn't heard anything back yet.

They do dual map other vehicles so it will be something worth investigating when they test & develop.

  • 3 weeks later...
crisis Contributor

crisis

Posted
Posted

I rang SAS today to get an update - they had my car there for a week doing development work almost a year ago, but held off pending availability of the replacement ECU.

Latest advice is they are waiting for us. - apparently there is a good number of M35s waiting to be tuned once the process is proven.

Is there anything I can do to progress this exercise.

m

  • 1 month later...
Bis-e Bee Mentor

Bis-e Bee

Posted
  • Author
Posted

OK guys, huge apologies.. all i can say is:

working = not enough spare time!

+

p platers in commodore's who can't drive and crash into other cars then refuse to pull over and exchange details suck! (don't worry, the licence plate is burnt into my memory!)

Tax cheque has arrived and I have been in touch with SAS, the car is going in with the spare ECU for a week hopefully at the end of November.

I'm opting for the dual map option but until they do the testing and development they are not sure this is a possibility, will update on this one.

I have one small concern with my nismo muffler that I'm hoping SAS can work with, I think it's locked in Silent mode and not sports :happy: When I flick the switch in the cabin and sound is no different, runs fairly quiet most of the time (i believe Goldzilla said it sounded like a vaccum cleaner lol). I'm guessing when the car was complied they just set the switch to silent and then disconnected/severed the cable or something. I think it may be restricting flow of the exhaust but my first tune will mainly be about fuel efficiency anyway, I'll worry about performance once the GCG highflow/intercooler and new turbo back exhaust is completed.

Once again sorry for my silence, I've been popping in now and again as I like to watch :)

Chow dudes

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Lithium
      Borg Warner EFR Series Turbo's V 2.0

      By Lithium · Posted

      Sorry had a bit of a week and haven't had heaps of time to follow this, so apologies if I've missed something - any chance of showing a log with the rpm, turbo speed, MAP, and wgdc all in one view? Definitely an "interesting" problem, and while it's definitely worth noting that there was a similar issue with the twins I'd not completely put all bets on the root cause being the same thing.  Keep an open mind, follow the data.
    • Borci88
      Borg Warner EFR Series Turbo's V 2.0

      By Borci88 · Posted

      I built this engine approximately 12 years ago so my own head (brain) is a little grey on the exact hardware in the RB head, however what I recall is. Stock RB25 NEO TURBO Intake Camshaft HKS 260 degree Exhaust Camshaft (R34 GTR) RB25 NEO Turbo Springs  I ported/removed the exhaust stud humps found in the RB25 head so theres less turbulence but it wasn't ported/polished properly, just a hump removal. I've attached two pictures of the before and after to illustrate.     The ECU gets its boost reference from the nipple on the rear of the head on the intake side, behind the fuel rail. The wastegate gets its boost reference from a nipple on the cooler pipe immediately after the comp cover.  Could a decent pressure drop across the intercooler cause the wastegate to be seeing a higher PSI than what the ECU is seeing, and thus it can't control it accurately and quick enough?   We ran a line to the actuator and watched it open and close using an air compressor, while we didn't have a gauge on the line to see when it was cracking open, it was opening smoothly.  I just removed the gate now and even though the documentation says you need to open it in a vice due to preload (which I did), there wasn't any preload on the cap, which is something we noticed straight out of the box as well when new. This silver cap internally is threaded to the actuator rod that runs out the bottom of the straightgate. Not sure how I'm supposed to get this spring out to be frank.. Potentially but everyone else doesn't appear to have to stop at 500kw because of 6boosts design.  I would, but I think I'm getting to that point where if I'm going to do the head and make another 100kw, then I'm going to need a fancy gearbox and quite a few other things and 10k becomes 20k becomes 30k within a few months. I'm not necessarily sold on the idea just yet that the head is restrictive at 4000rpm (and what.. 300kw?) and yet doesn't seem to be restrictive at 7000rpm when it's making 500kw, however I'm obviously not closing the door on that theory.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Yeah - Half the problem is I know this sensor actually goes to 150C.. I'm pretty certain it is min of 11C. So still more data required I suppose. It's really quite hard to get the oil temp to 100+ then immediately pull over and take a reading before the temp drops. Annoyingly I suppose the range I really 'want' is likely 80 -> 120C. TBH the ecu can't really *do* anything with it, and the gauge itself is very visible... ...but you know how it is.
    • The Mafia
      Borg Warner EFR Series Turbo's V 2.0

      By The Mafia · Posted

      My EFR 8474 Black, made 800awhp on a roller dyno. at 25-26psi. E85. Shaft speed was around 106,000rpm 1.01 rear. The rear is maxed.  6 boost Turbosmart 60mm gate 3.5inch exhaust  Head is worked to the shithouse. Bain racing. VCam. 272 exhaust. RB28 - RB26 foundation.  You have an intake issue. Start getting proper data and I mean go back to the simple things.  - Pressure test your intake - Block off the Turbo BOV, you don't need it.  - Test pressure before and after your intercooler If your head is pretty stock, that is your issue. Especially if it is NA.  Take it off and spend $10k on it. 
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Temp = -21.052 X Voltage + 114   That should get you pretty close. Calcs based on two points I could do easy calcs on (30 and 70 degrees).   It also says your sensor should only read as low as 9 degrees when it maxes out at 5V, and should hit a peak of 114 degrees at 0V... Just as a heads up if you were going really cold places, or wanting to be aware when temps really go up with it.
×
×
  • Create New...