Jump to content
SAU Community

Recommended Posts

Noo, not for the GTR... had you going though.

For this:

http://www.carsales.com.au/all-cars/privat...2&silo=1011

I am clueless apart from the fact that I heard somewhere that Uni and TAFE students need practice etc and will provide cheap service as it's not professional per se'. Anyone know anything more than that or know someone who had a car resprayed by a student?

P.S. I might buy the Escort.

Link to comment
https://www.sau.com.au/forums/topic/280501-unitafe-workshops/
Share on other sites

TAFEs can do it, you have to pay for the paint, thats it, if they don't do it good enough, they and it back and try again, so it might be gone longer than with a paint shop, but is cheaper. Ring an actual TAFE (whichever one spraypainting is at), and ask them for some more info.

Not sure if Uni's do it ?

I had a friend have it done many years back now at TAFE i think the thornlie one but dont quote me on that... she did have to take it back to get a small bubble patch fixed up and they did rub it back and do it correctly and i have to say the job looks great now, they have to meet industry standards and the tutor is always there to check... just be aware the car is gone for almost a whole semester as it is a training tool and make sure it cannot be started :P

im pretty sure its much less than 3000. i went to carlisle tafe and a couple of the spray painters there said all u gotta do is pay for paint and wait bout 3 weeks. correct me if im wrong but as far as i know paint only cost's $400-$500 max.

also students get assessed on the job so everything must be done by the books!

yes carlisle tafe will do it. paint shouldnt be anything over 800 to 1000 and the job will be done properly as resprays are usually done by the 3rd and up year apprentices .i have to do one next time i head to tafe. car usually has to be totally stripped and in decent condition if its just getting paint work

I went to see the car today, needs a bit of body repair but the current owner is a panel beater so he's been doing the work himself.

I asked if he would do a bit more work on the body as I have no idea about that stuff.

Drives nice apart from a flat spot in second due to an over sized cam installed, needs a tune.

  • 4 months later...

Nah, not long after I looked at the Escort I went and signed the papers to build a house so I never got the Escort...

Then it was taken off carsales because the guy wanted to respray it himself. I have been keeping an eye out for it to buy it off him.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Saw this video today from Adam LZ.    Long story short is he is claiming that the load from the engine fan once the fan clutch heats up(engaged) is increasing the getrag rattle(at idle) when you don't have a dual mass flywheel.  Before I go buying an electric fan setup .... Anyone heard of this ?    I must admit when my car is cold the getrag is pretty quiet and I do notice the rattle after it is all warmed up. I've always assumed this is due to the gearbox oil temp and tolerances of metal.       
    • Yep it sure does.   Tone wheel lines up in the same spot perfectly.    
    • Something I meant to say when we were chatting the other night about having an open trailer floor being great to work on a car, but you've never used the feature... It's a great place to park a car after doing suspension component changes, and do the tightening of all the bushes with the car sitting at full ride height. Especially when you don't have a 4 post hoist!
    • That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
×
×
  • Create New...