Jump to content
SAU Community

Recommended Posts

Hi guys,

Battery went flat a few days ago, battery is about 6 years old as it is an 03 model. Battery cells were gone.

Had the battery replaced. Went to the petrol station to fill up about 3 km's down the road. Locked the car then unlocked. Went to start the car and the rpm's went up as normal then dropped which lead the car to turn off. Oil, battery and engine light came on. Second attempt same symptoms. Third attempt turned on however this time the rpm completely dropped just above 0 then all of the sudden went back to 700rpm drove off as car was running. On the third attempt it almost sounded like the car wanted to turn off. Got home locked the car and left it locked for about an hour, i again attempted to turn the car on same thing engine turned on, rpm dropped all the way and turned off.

Please help my auto electrician does not know what is wrong with the car, it is the first time he has worked on a car like this.

Kind Regards Yianni

Link to comment
https://www.sau.com.au/forums/topic/280543-2003-350gt-coupe-starting-problem/
Share on other sites

Hi Chris not to sure.

I have been doing some research on a few infiniti websites and sourced another person that had the same problem. He referred to the procedure on how to reset the ecu, throttle pedal release and idle air volume learning and it seemed to have resolve his issue so i might give that a go. Its definitely not an immobiliser problem as for starters the car would not even turn on. Apparently the battery of the car was disconnected overnight so it reset the ecu however the auto electrician didn't teach the ecu which regulates the idle etc.

Edited by T88turbo

hey guys this might sound realy stupid, though i had the same problem, and it wasnt my ecu or battery... it was acutally my spark plugs..... when was the last time u checked your plugs? see if there is any oil getting to these plugs, if so see a mechanic.

Nope plugs were replaced 2 months ago.

It only happens on hot starts, its all normal when the engine is cold. This is because when the engine is hot it does not need to rev high, revs drop instantly to about 600rpm as normal.

Stuff it im going to take it to nissan, i bet you its the ecu that needs to be programmed. Remember the ecu regulates the idle, and a thousand other things. I tried this procedure on the infiniti website that resets and teaches the ecu but it didnt work.

Here is the link if you need it.

http://www.nicoclub.com/articles.php?id=356397

Now that you mention it, my 300gt has been doing this as well..

On hot starts, revs drop really low and on a few occassions stalled. Most times, after starting, I just rev it a little and its all good.

has never stalled on me when actually driving only when starting the car. Might have to look into it a bit more.

thought about the fuel type you have been using?? i have another car that has trouble starting when i use shell fuel. BP and mobil have been fine. friggen italian cars! lol

it might be as simple as that for you

hi bilistic,

Did you have your battery disconnected more than 24 hours? I can understand the ecu learning your driving habbits however how does it learn not to stall on hot start ups by reving it are you sure this worked? and did it stall at the beginning when you had your battery changed? I can't understand why it doesnt stall on cold start ups???

hi bilistic,

Did you have your battery disconnected more than 24 hours? I can understand the ecu learning your driving habbits however how does it learn not to stall on hot start ups by reving it are you sure this worked? and did it stall at the beginning when you had your battery changed? I can't understand why it doesnt stall on cold start ups???

hey mate

yeh i had my battery disconnected for over 1 week when i installed the plenum spacer (long story lol)

when i finished the install i reconnected the battery and i did an ecu reset straight away before i even started the car again

the car started fine and i took it for a 20min test drive for the ecu to start learning again. i got home and parked the car. i had to move the car again after 5 min and when i started the car - stall.

It kept doing this for about 1 week. Cold starts were always fine. Any start where the engine went into cold start mode (higher revs than normal) it didnt stall. When it was hot (example, went to petrol station to fill up, turn on car - stalled) the car stalled. To get around it stalling, every time i started the car i just blipped the throttle to make sure it didnt stall. I was doing this so, that like you i was going to go and get it checked out.

However, after about 1 week, the problem went away. now i can start my car and its like back to normal again.

Hope this helps.

I use BP Ultimate 98 Octane all the time since i have had the car, and the previous owner did also.

Edited by BLISTC

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...