Jump to content
SAU Community

Can Someone Turn Up Some Locating Bushes For Me?

Mr GTS4

By Mr GTS4,
in Fabrication

 Share

Recommended Posts

Mr GTS4 Mentor

Mr GTS4

Posted
Posted

need some bushes made up.. 4 of in total then need to be about 10mm long with the inside diameter of 12mm and the out t obe 14mm

They are to be used as below

"the calipers mounting holes are the same centers as the stagea hub. so to fit the caliper to the hub you need to get a M12 x 1.25mm bolt with a thred length of 50-52mm. make a bush to locate the bolt in the center of the stagea hubs hole, i'll be using stainless and turning it up at work, i'd also recommend using a decent material as a bush (mild or stainless)"

if you can send me a email at - [email protected] and give me a price that would be great!!!

Thanks

Curt

Duncan Grand Master

Duncan

Posted
Posted

its kind of the opposite problem, the caliper takes m12 but the hub is drilled out to m14. So either drill and tap the brakes out to m14 (but they already have some sort of high tensile insert) or use m12 bolts with a bush around for a snug fit in the hub.

If someone sources say 1m of the right ID and OD tube they could flog it off in 2cm lengths for people with this problem

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Question about BoV on RB25DET NEO

      By MBS206 · Posted

      Something to note, on an aftermarket BOV, it's quite possible to end up with the worst of both worlds, where on light throttle, there isn't enough force to open the BOV so you get small reversion and driveability issues, and with the venting to atmosphere, it dumps a lot of fuel on shifts. Realistically, dumping to atmosphere under power isn't a major driveability issues, compared to the issues of stalling from reversion. If you're getting up the throttle, then putting the clutch in, say on a shift up, but then don't release the clutch, yes, the engine can and will stall, but, just drive around it, and that's easy, let the clutch out in the next gear and the car rolling will keep it all running / going.who wants a hard hit of throttle and then to just let the motor idle anyway?   Main issue for driveability is blipping throttle and it wanting to stall, like when parking or trying to move in slow traffic.
    • soviet_merlin
      2020 Nissan Skyline 400R V37/Infiniti Q50 RS insurance in NSW

      By soviet_merlin · Posted

      As in they quoted one price, you mentioned the exhaust, and they promptly added $200 on top? Interesting.
    • GTSBoy
      Question about BoV on RB25DET NEO

      By GTSBoy · Posted

      Note that I'm not suggesting this is a great idea. Just saying that it is something that could be done to achieve a better outcome than the more shit ideas will provide.
    • luke gtr
      What's this Foreign Object?

      By luke gtr · Posted

      I'd try removing it, connecting hoses and see if that helps. Depending on specs, it could actually be restricting the flow(it also might be helping).
    • GTSBoy
      Question about BoV on RB25DET NEO

      By GTSBoy · Posted

      Yes, that's a hybrid BOV. The adjustable spring load ones are about making teh pressure build up higher before venting, so you get a more agressive whoosh. That is not what I meant or what you want. By "restricting", I don't mean "keep it closed until the pressure is higher, then open it fully". I mean "open it as soon as it is required, but only have a small port area, so that the flow rate out of it is slowed down". The pressure will rise to be higher than a bigger ported BOV would provide, but it would do while it is venting. The idea is to slow down the rate at which the replacement eair is flowing past the AFM, to reduce the magnitude of the air flow signal peak, to reduce the amount of fuel that is added per revolution.
×
×
  • Create New...