Jump to content
SAU Community

Recommended Posts

Ok, I've got no idea what has happened to my previous post...

Anyway, I've got a 11/97 Autech 260RS Stagea with genuine 73,000kms which I am currently wrecking. I was planning on doing an engine/manual gearbox conversion into my RS4, however have decided against it.

The 260RS shares most of the running gear with R33 GTR's eg. engine, gearbox, LSD, brakes etc.

RB26DETT engine comes complete with loom, ecu, manifolds, turbos but missing the afm's. The car was hit in the front, therfore the harmonic balancer was damaged. I have found a replacement one which will be included. The engine and gearbox are still in the car. - $4500

Twin Plate Exedy clutch, (only 1000kms old) - $1500

Manual gearbox - $1000

Brembo brakes complete with rotors and lines - $1900

Nismo front pipe (fits 260RS or R33 GTR) - $500

Used Hi Flow cat converter with 3" flanges - $80

New Trust Pillar Pod 60mm (fits R33) - $100

All prices are open to offers.

Parts are located in Adelaide (Aberfoyle Pk) however I'm happy to post interstate.

Please contact me via pm.

Cheers

Daniel

post-13694-1248863163_thumb.jpg

post-13694-1248863176_thumb.jpg

post-13694-1248863197_thumb.jpg

post-13694-1248863215_thumb.jpg

post-13694-1248863255_thumb.jpg

post-13694-1248863280_thumb.jpg

post-13694-1248863301_thumb.jpg

post-13694-1248863322_thumb.jpg

post-13694-1248863339_thumb.jpg

post-13694-1248863360_thumb.jpg

post-13694-1248863378_thumb.jpg

more info on the twin plate please!!!

pull type?

exactly what twin palte is it? carbon? hyper metal?

cheers

It's a pull type.

Receipt says it's a Exedy Twin Plate Hyper, sorry I don't have any more info or pics yet as it's still in the car. I'm hoping to have it out within the next few days.

Cheers

Daniel

Brembo calipers sold (pending payment)

Front and rear rotors and lines still available - $200 the lot.

Fronts are 324mm and rears 300mm.

Assume front pipe is 3"? Can you find out postage to Perth 6010? Cheers..

Yes the front pipe is 3".

Postage to Perth is $50.00.

Cheers

Daniel

Pair of factory air deflectors, these bolt on to the caster rods.

Excellent condition - $100 neg.

post-13694-1249100112_thumb.jpg

post-13694-1249100126_thumb.jpg

Edited by RSFour
  • 2 weeks later...
  • 2 weeks later...

interested in the engine.

do you know compression on the cylinders ?

would you provide some sort of warranty ?

please pm me mate :)

Any know issues with engine?

Do you know compression stats? Please pm back! Thx

interested in the engine.

do you know compression on the cylinders ?

would you provide some sort of warranty ?

please pm me mate :)

PM's sent guys.

Brembo calipers and Nismo front pipe - sold.

Here's a pic of the Exedy clutch.

post-13694-1251377450_thumb.jpg

  • 3 weeks later...

Here are a some pics of the gearbox.

Also, for anyone interested the Exedy clutch is still available.

Cheers

Daniel

post-13694-1253110653_thumb.jpg

post-13694-1253110665_thumb.jpg

post-13694-1253110676_thumb.jpg

Yes

[/quote

I have the 260RS with N1 motor. Dont know what clutch this would have fron Autech ?What did

you pull out of yours when replaced ? Single plate no doubt ! About to put big dumps and Haltech

under it, and got to thinking the clutch to be a possible issue here ! Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...