Jump to content
SAU Community

Recommended Posts

Hi.

I am looking to buy a new car for myself, however I noticed that all the dealer's cars have very low km's on them. (e.g. 60,000 - 80,000km). This seems impossible considering the cars are 10-11 years old. (the r34 turbo's in particular)

I believe the cars have been around the clock once before or someone has reset them... but not real sure.

If any one could help me out here it would be greatly appreciated.

Thanks, From Luke.

Link to comment
https://www.sau.com.au/forums/topic/281433-buying-from-a-dealer/
Share on other sites

there are a few things to remember about cars from japan. 1: japan is a small place so that means that not much long driving is done. 2: japan has a very good public transport system so some people with cars won't drive them all the time. 3: while the car may only low kms on it, even if they are genuine kms, the engine may have much more wear than that due to sitting in traffic for long periods of time. the engine is still wearing while it is idling.

but yes, most imports that come into australia have had some 'tweaking' done. the biggest issue that this creates is that it can then mean that the timing belt gets left until well overdue before it is changed. however there would be some genuine km cars that come in. i have a 9 year old pulsar with 50,000kms on it. i have owned it for 6 years and only put 27,000kms on it in that time.

when looking at a car it is best to compare the kms on the clock to the condition of the car. if the car is extremely neat and has low kms then there is more chance of it being genuine, but it is going to be a good buy even if the kms are a bit higher than what the odometer says. if the kms are low and the car looks a bit tired then it is a bit obvious that things are a bit suss. but it is a case at looking at the right things. just because it has dodgy panels doesn't automatically mean the engine has done lots of kms.

  • 5 weeks later...
when looking at a car it is best to compare the kms on the clock to the condition of the car. if the car is extremely neat and has low kms then there is more chance of it being genuine, but it is going to be a good buy even if the kms are a bit higher than what the odometer says. if the kms are low and the car looks a bit tired then it is a bit obvious that things are a bit suss. but it is a case at looking at the right things. just because it has dodgy panels doesn't automatically mean the engine has done lots of kms.

^^^ Ditto

An extra item to look at is the set of Keys.

I have a GT-R with only 34500Kms with Japanese history & I'm the 1st owner in Oz.

Carpet's like new.

Seat Bolsters are like new.

Steering Wheel is like new.

And since I have a full complememt of transponder keys, you can tell that all the keys are like new.

(So have a look at the key teeth as well as all other checks and balances)

Along with everything thats been mention, always should get the car checked out by a mechanic that you trust before you hand over the cash, because that way, even if you think the car is all good and clean, a experienced mechanic can tell you exactly what sort of condition the car is in.

But to be honest, I think buying a R34 GTT off a dealer is a bit of a rip.... They all put up the price and over charges everyone ($20,000-$25,000).

I think it's better off buying it privately, but just make sure you get the car checked out before you buy it. That way, you might save yourself a few grand. I just bought my manual GTT for $16,500 on the road off carsales, its got 105,000km on the clock, but the condition its in, is immaculate, its so good that the seller even serviced the car with nissan lol :laugh:

^^^ Ditto

An extra item to look at is the set of Keys.

I have a GT-R with only 34500Kms with Japanese history & I'm the 1st owner in Oz.

Carpet's like new.

Seat Bolsters are like new.

Steering Wheel is like new.

And since I have a full complememt of transponder keys, you can tell that all the keys are like new.

(So have a look at the key teeth as well as all other checks and balances)

im not saying that your cars km's arnt geniune, but it is possible that they could just replace all those things you mentioned to make it look new...trust me some people have extreme measures.

im not saying that your cars km's arnt geniune, but it is possible that they could just replace all those things you mentioned to make it look new...trust me some people have extreme measures.

Possible? Yes it's possible. You've used the correct word "...possible..."

But when you are discriminating and collecting 'jigsaw puzzle' pieces that fit and fit well, you then take the next step...

eg wife reads all the Japanese paperwork

eg take along a mechanic familiar with the Skyline

eg take along a panelbeater

eg compression testing

eg 100s of messages thru the steering wheel and the seat yaddayadda

Even buying from a Dealer can contain pitfalls when all the Dealer wants to do is 'sell another car' > CAVEAT EMPTOR

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...