Jump to content
SAU Community

Recommended Posts

Ok All,

B4 I get pounced on by those who would happily tell me to go to the g35Driver.com website to find the answer, I have been there and even searched Yahoo for the wiring diagram for my 2002 V35 Sedan Bose Unit. The diagrams don't match those in our JP versions.

So far, I have dismantled all the interior lining of the boot and exposed the connector plug to the Bose Amp and it is a 26 Pin connector.

Does anyone have the wiring diagram to the stock Bose Head unit and the Bose Amp?

And, are the Bose Amps on coupes different from the Bose Amps on the sedans? I know the coupes don't have a subwoofer, whereas the sedans do...I aslo heard the subwoofer unit has it's own amplifier, not sure if it's true though...

This will save me a lot of time playing lottery with the wires. I can't afford to have this done by a professional nor can afford to buy a direct adaptor connector. FYI - I am jobless and refuse to go on the dole....

Any help will be appreciated....

Pic of Bose Amp:

aDSC00124.jpg

Pic of the connector 01:

aDSC00119.jpg

Pic of the connector 02:

aDSC00121.jpg

Pic of Bose Subwoofer:

aDSC00126.jpg

Link to comment
https://www.sau.com.au/forums/topic/281620-head-unit-wiring-diagram/
Share on other sites

I do. that said hat exactly are you trying to do?

if its pull the radio then the poor mans version will be on installdr.com. its the later model plugs and they do give the pinouts on that site.the colours WILL NOT match but the pinout will. if you have $15 buy an adapting lead from autobarn and match the colours. you will have sound albiet entirely too much at once but it will work.

forget about the bose amp side of things. you have already said that you do not have the $$ to get the proper lead. theres a pinout for the OEM amp in the 2003 FSM that is close.

I'm not too sure how technical you are but there s another way to tackle this but it invloves a lot of chasing and cuttng.

Funny you guys should mention made in PRC, I just bought a cheap all-in-one 7" double din touchscreen with Nav/HDTV/Ipod Interface/DVD Player/Reverse Cam input for very cheap...

I couldn't skimp on the fascia, and despite Chris's views on the Metra Unit, I went and bought it from the USA. This is the same unit that JB Hi Fi supposed tried to sell BenzLe. Apparently, everyone bags the Metra Unit due to the A/C probs, but after closer reading, the culprit lies in the pin connectors on the fascia...

I then bought a chinese wide angle reverse cam to replace the factory one and also some reverse sensors.

So once everythign arrives, I will start ripping out the JP Panasonic Nav Brain, Bose Headunit, Factory Reverse Cam, 7" panasonic Screen, etc....

Thanks for the website Chris. I'll try my luck, and go buy a Nissan harness adaptor like you have recommended...

If the whole Bose Amp and Speaker system needs rewiring, I am prepared to do so...since a jobless person should have plenty of time up their sleeve...

Even on a 'tight-ass' budget, replacing the stock unit for an aftermarket one isn't cheap at all, when you factor in all the other sundries required for a decent installation...Hopefully I can recoup some money by selling the Bose head unit with 6 stack MD Player, the fascia, Factory reverse cam, Panasonic 'add-on' system...Sometimes i scratch and wonder why I bought another imported car after the many hard and costly lessons learnt from previous experiences...

Hopefully, when I am done, I can put up a DIY and confirm the harness pin IDs...

Hey guys...

I am also attempting to install a double din headunit also...I actually bought the facia kit from JB hi fi, and it seems my climate control is working good. however there are 3 white plugs but in need of the circuit diagram for the audio...will check out the link....

driving around with half the dash missing....soo annoying...

  • 3 months later...

i'm looking at the audio wiring diagrams. This after my failure to identify the wiring in the skylines. How different is the skyline (non bose)audio system than the g35. The wiring colour codes are not like anything I have seen on this side of the pond.

Shouldn't be too hard...takes trial and error, a volt meter, and a fused bulb screwdriver....u can normally pick out the wire pairs for the respective speakers also. Normally, the thickest wire is the Constant +ve.

Anyway, if you can't do it yourself, go get it professionally done....

  • 14 years later...

Hi Chris,

 

long time since your post, just wondering if you have the Pinout for the v35 stereo plugs, I bought the roem nis2 harness but it doesn’t match the v35 connector.

any help appreciated, I can work out the grn and power constant. But the rest might be hard.

thanks

Tyson

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • How much have you lowered?  I had 350Z springs in the rear and was able to pull the camber into factory spec with the factory arms on the rear, obviously the front ran negative camber as it isn't adjustable, but rotating the wheels regularly evened out the wear.
    • Either the installer needs to come back, you need an auto electrician, or you need to learn automotive electricals yourself.   First step Id look at is where that big thing came out of, is there still things unplugged at that location? Maybe they just forgot to put a relay in or something?
    • Well, this is probably where a wiring diagram and a multimeter come into play.
    • I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
×
×
  • Create New...