Jump to content
SAU Community

Recommended Posts

This morning on the way to work my R32 kept hitting fuel cut when I was demanding power from it,

if you stomped first gear most of the time it would pull through but towards the end of second gear it would hit fuel cut, not every time but just most of the time

tis a RB20 with R33 Turbo, FMIC & Manual Boost Controller.

plugs are at 1.0 gap atm which I need to reduce

why do Rb20's hit fuel cut? could it be the fact I have a spiking boost controller? or perhaps that it was too cold this morning? I havnt touched my boost level which is about 13psi last time I set it, I dont have a boost gauge so I am not sure how much boost it runs when it hits fuel cut, but its been running fine until now.

My Ribs are sore now

Edited by BANGN
Link to comment
https://www.sau.com.au/forums/topic/282034-rb20-keeps-hitting-fuel-cut/
Share on other sites

This morning on the way to work my R32 kept hitting fuel cut when I was demanding power from it,

if you stomped first gear most of the time it would pull through but towards the end of second gear it would hit fuel cut, not every time but just most of the time

tis a RB20 with R33 Turbo, FMIC & Manual Boost Controller.

plugs are at 1.0 gap atm which I need to reduce

why do Rb20's hit fuel cut? could it be the fact I have a spiking boost controller? or perhaps that it was too cold this morning? I havnt touched my boost level which is about 13psi last time I set it, I dont have a boost gauge so I am not sure how much boost it runs when it hits fuel cut, but its been running fine until now.

My Ribs are sore now

hey im driving a rb20 with a turbo on aswell and im having an issue with an electronic boost controller, my solonoid doesnt regulate any air going into the turbo, but yeah mine was hiting fuel cut aswell and since i took the boost controller out of the mix it seems to be fine, might want to try that? take it out and if it stops doing that then its most likley a boost issue

hope that will helps in some way.

i would say it is the cold air causing it now and not before. when i had my 33 i was having the same issue on cold mornings when i had the boost at similar levels.

i think that happens to my 33 as well, but only at cold start on a cold day, but i do not dare push it before the engine warms up

You should turn the boost down and see if that helps over the next few days. Just make sure you turn it down and not up. haha

Yer i would try it first coz the ecu is proberly cutting the fuel out having higher boost.

Get yrself a stage 3 chip in the ecu to eliminate the default fuel, speed, revs, boost cut out.

Ecu chips arent expensive and they will make the car perform better. :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...