Jump to content
SAU Community

Hicas

sturb25

By sturb25,
in Four Door Family & Wagoneers

 Share

Recommended Posts

QWK32 Veteran

QWK32

Posted
Posted
That's exactly what I had but without the heavy steering. :) Definite crab walk. Happens at higher speeds like 80km/h and you need to steer into it and if slow down quick a flick out of it. I recently had work done on the suspension but the steering wheel is not that straight after the alignment and wondered if that had anything to do with it...? Speedo cable is all good.

well if the steering wheel isn't straight that'll be your problem. there are two sensors up in on the steering column that tell the HICAS ecu that you are turning the steering wheel and which way. if your traveling along at at higher speeds, when HICAS becomes active, and because your steering wheel isn't straight the steering sensor is registering that you are turning the steering wheel, even though you really aren't, it will make the HICAS start steering. if your ok to do it yourself just pop the steering wheel off and line it up straight, or just take it back to the place that did the alignment and tell them to sort it out.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4755500
Share on other sites
QWK32 Veteran

QWK32

Posted
Posted
Having a think the sensors aren't in the wheel itself, so the wheel could be on upside down and it wouldn't effect anything. Looks like I'll have to lock up the HICAS.

correct the sensors are mounted to the steering column and the steering wheel boss activates the sensors when you turn the wheel. you should be able to slide the whole steering wheel boss off and jump it over a spline. it will require a fair bit of persuasion to get it off though.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759332
Share on other sites
GT-R32 Grand Master

GT-R32

Posted
Posted
correct the sensors are mounted to the steering column and the steering wheel boss activates the sensors when you turn the wheel. you should be able to slide the whole steering wheel boss off and jump it over a spline. it will require a fair bit of persuasion to get it off though.

Okay, sweet. Thanks again Josh.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759336
Share on other sites
zei20l Grand Master

zei20l

Posted
Posted

if you havent removed a steering wheel before, be VERY careful and dont remove the nut completely before you attempt to remove the wheel. leave it on a few turns so it doesnt smack you in the face when youre wiggling it off!

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759350
Share on other sites
Daleo Grand Master

Daleo

Posted
Posted

Thing is, if the steering wheel wasn't removed immediately prior to this issue, it can't have moved on the spline.

Removing the wheel and re-orienting it will not correct the original source of the problem.

The rack centre position could be offset to one side, causing your problem.

You should turn the wheel from centre to lock in each direction counting the number of turns, if it is unequal in either direction, any adjustment should be made at the rack ends with the rack centred.

Then you can be sure that your rack (and therefore) steering column and wheel are centred correctly.

Good luck.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759796
Share on other sites
M I K E Mentor

M I K E

Posted
Posted
That's exactly what I had but without the heavy steering. :) Definite crab walk. Happens at higher speeds like 80km/h and you need to steer into it and if slow down quick a flick out of it. I recently had work done on the suspension but the steering wheel is not that straight after the alignment and wondered if that had anything to do with it...? Speedo cable is all good.

what work did you have done to the suspension? height adjustment by any chance?

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759895
Share on other sites
GT-R32 Grand Master

GT-R32

Posted
Posted
if you havent removed a steering wheel before, be VERY careful and dont remove the nut completely before you attempt to remove the wheel. leave it on a few turns so it doesnt smack you in the face when youre wiggling it off!

Hahaha I've done it a couple of times so won't have that problem!

Thing is, if the steering wheel wasn't removed immediately prior to this issue, it can't have moved on the spline.

Removing the wheel and re-orienting it will not correct the original source of the problem.

The rack centre position could be offset to one side, causing your problem.

You should turn the wheel from centre to lock in each direction counting the number of turns, if it is unequal in either direction, any adjustment should be made at the rack ends with the rack centred.

Then you can be sure that your rack (and therefore) steering column and wheel are centred correctly.

Good luck.

Great post, thanks for that.

might also been the rack bushes too! if they are stuffed, it will cause the rack to move also. its possible its just jammed in the wrong position.

I only just had them done. If some things weren't done correctly can that lead to these issues?

what work did you have done to the suspension? height adjustment by any chance?

Bilstien coilovers, cambers kits and traction rods and all sorts of random shit. I really don't know a whole lot about suspension sorry. :( But definitely height has changed, it's certainly lower.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4760905
Share on other sites
  • 1 year later...
Raysboostin Mentor

Raysboostin

Posted
Posted

open your eyes before your mouth please

pull ur head in smartass, i was making a valid point about a possible scenario. which has nobody has proven otherwise or posted anything to the contrary. its entirely possible that if the front washed out on turn in, that the rear turning away from the corner could turn you off the road/track. maybe not a common situation but possible none the less.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-5918242
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • SeanR32GtSt
      Hypergear Turbochargers and High flow Services Development thread

      By SeanR32GtSt · Posted

      Lower at the hubs. Funny I forgot to mention that part. Do this pull here I turned the camera off too soon but the graph shows a drop at the top and that was because the pipe from the turbo blew off. The tuner said we could’ve made possibly another 15 whp. He also added if I switched to ethanol we could up the boost some more as well. I was comfortable capping it at the most of 20 pounds. Turns out the turbo pipe just needed a new worm clamp. Got home replaced that then did a third gear pull from 3k to 7200 rpm and the power was great to the top. I just got an ecu mounting bracket from IEE that I need to try and get everything to fit well. It’s a PITA to get the harness and ecu fit properly behind that kick plate 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      He means "as opposed to mechanical cable drive". Older cars (R32 for ex.) had cable drive. Later cars with essentially the same gearbox, ie R34 GT (NA RB25) used essentially the same box as the R32 GTSt, but instead of a cable drive, had an electronic speed sender plugged into the same hole in the box, running from the same little gear that would have run the cable. Some of the shittier later cars use a speed sender on the nose of the diff, or the ABS sensors.
    • GTSBoy
      Hypergear Turbochargers and High flow Services Development thread

      By GTSBoy · Posted

      Lower than engine, or lower than it should at the hubs? Either way, that is a nice power figure and I'm not surprised you say it rips now. What stopped you from turning it up any more? Injectors? Or did it just stop responding to boost?
    • SeanR32GtSt
      Hypergear Turbochargers and High flow Services Development thread

      By SeanR32GtSt · Posted

      Got my 34 gtt tuned last week. Car made 362 wheel horsepower at 19 psi. Turbo was the ATR43SS. Only other upgrades were haltech 2000 series. 650cc injectors, walbro 250, fmic. Pro hub dyno reads 6% lower than actual figure according to my tuner. Car is a real ripper now.  IMG_7261.mov
    • DraftySquash
      Looking for someone with a R34 front bar

      By DraftySquash · Posted

      Hi everyone, I'm wondering if anyone in Melbourne (preferably West) has a non-S2 R34 front bar. If it's already off the car, even better!  Nothing too weird, I just need to get a cut-out of the hole that the front indicators clip into 🤣 (image attached for reference)   I've got a front bar from JSAI Aero, but those holes need to be cut myself, and I want to get it right so the indicators will clip securely. And my OEM bumper is a S2, so I have no reference. So looking for a member who might be able to spare me a few minutes to make a cardboard cut-out using your front bar.
×
×
  • Create New...