Jump to content
SAU Community

Hicas

sturb25

By sturb25,
in Four Door Family & Wagoneers

 Share

Recommended Posts

QWK32 Veteran

QWK32

Posted
Posted
That's exactly what I had but without the heavy steering. :) Definite crab walk. Happens at higher speeds like 80km/h and you need to steer into it and if slow down quick a flick out of it. I recently had work done on the suspension but the steering wheel is not that straight after the alignment and wondered if that had anything to do with it...? Speedo cable is all good.

well if the steering wheel isn't straight that'll be your problem. there are two sensors up in on the steering column that tell the HICAS ecu that you are turning the steering wheel and which way. if your traveling along at at higher speeds, when HICAS becomes active, and because your steering wheel isn't straight the steering sensor is registering that you are turning the steering wheel, even though you really aren't, it will make the HICAS start steering. if your ok to do it yourself just pop the steering wheel off and line it up straight, or just take it back to the place that did the alignment and tell them to sort it out.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4755500
Share on other sites
QWK32 Veteran

QWK32

Posted
Posted
Having a think the sensors aren't in the wheel itself, so the wheel could be on upside down and it wouldn't effect anything. Looks like I'll have to lock up the HICAS.

correct the sensors are mounted to the steering column and the steering wheel boss activates the sensors when you turn the wheel. you should be able to slide the whole steering wheel boss off and jump it over a spline. it will require a fair bit of persuasion to get it off though.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759332
Share on other sites
GT-R32 Grand Master

GT-R32

Posted
Posted
correct the sensors are mounted to the steering column and the steering wheel boss activates the sensors when you turn the wheel. you should be able to slide the whole steering wheel boss off and jump it over a spline. it will require a fair bit of persuasion to get it off though.

Okay, sweet. Thanks again Josh.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759336
Share on other sites
zei20l Grand Master

zei20l

Posted
Posted

if you havent removed a steering wheel before, be VERY careful and dont remove the nut completely before you attempt to remove the wheel. leave it on a few turns so it doesnt smack you in the face when youre wiggling it off!

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759350
Share on other sites
Daleo Grand Master

Daleo

Posted
Posted

Thing is, if the steering wheel wasn't removed immediately prior to this issue, it can't have moved on the spline.

Removing the wheel and re-orienting it will not correct the original source of the problem.

The rack centre position could be offset to one side, causing your problem.

You should turn the wheel from centre to lock in each direction counting the number of turns, if it is unequal in either direction, any adjustment should be made at the rack ends with the rack centred.

Then you can be sure that your rack (and therefore) steering column and wheel are centred correctly.

Good luck.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759796
Share on other sites
M I K E Mentor

M I K E

Posted
Posted
That's exactly what I had but without the heavy steering. :) Definite crab walk. Happens at higher speeds like 80km/h and you need to steer into it and if slow down quick a flick out of it. I recently had work done on the suspension but the steering wheel is not that straight after the alignment and wondered if that had anything to do with it...? Speedo cable is all good.

what work did you have done to the suspension? height adjustment by any chance?

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4759895
Share on other sites
GT-R32 Grand Master

GT-R32

Posted
Posted
if you havent removed a steering wheel before, be VERY careful and dont remove the nut completely before you attempt to remove the wheel. leave it on a few turns so it doesnt smack you in the face when youre wiggling it off!

Hahaha I've done it a couple of times so won't have that problem!

Thing is, if the steering wheel wasn't removed immediately prior to this issue, it can't have moved on the spline.

Removing the wheel and re-orienting it will not correct the original source of the problem.

The rack centre position could be offset to one side, causing your problem.

You should turn the wheel from centre to lock in each direction counting the number of turns, if it is unequal in either direction, any adjustment should be made at the rack ends with the rack centred.

Then you can be sure that your rack (and therefore) steering column and wheel are centred correctly.

Good luck.

Great post, thanks for that.

might also been the rack bushes too! if they are stuffed, it will cause the rack to move also. its possible its just jammed in the wrong position.

I only just had them done. If some things weren't done correctly can that lead to these issues?

what work did you have done to the suspension? height adjustment by any chance?

Bilstien coilovers, cambers kits and traction rods and all sorts of random shit. I really don't know a whole lot about suspension sorry. :( But definitely height has changed, it's certainly lower.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-4760905
Share on other sites
  • 1 year later...
Raysboostin Mentor

Raysboostin

Posted
Posted

open your eyes before your mouth please

pull ur head in smartass, i was making a valid point about a possible scenario. which has nobody has proven otherwise or posted anything to the contrary. its entirely possible that if the front washed out on turn in, that the rear turning away from the corner could turn you off the road/track. maybe not a common situation but possible none the less.

Link to comment
https://www.sau.com.au/forums/topic/282242-hicas/page/2/#findComment-5918242
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • MBS206
      NC MX5

      By MBS206 · Posted

      Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • turbo76lx
      Torana Lx Gtr Hatch, Lots Of Pictures

      By turbo76lx · Posted

      Sorry I meant that we are building the EH for a client.
    • The Bogan
      Torana Lx Gtr Hatch, Lots Of Pictures

      By The Bogan · Posted

      LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...