Jump to content
SAU Community

Problems With R34 After Comming Out Of Storage

Pandoraa

By Pandoraa,
in Engines & Forced Induction

 Share

Recommended Posts

Pandoraa Contributor

Pandoraa

Posted
Posted

Hello all,

My R34 GT has been in storage for the last few months. Have just bought it out to start cleaning it up and doing some work on it.

Battery was dead which is to be expected... Started it up with jumpers and left it to run for a good 20 minutes.

However the main problem is there appears to be a grinding sound coming from the engine bay. (sounds like a mix of grinding and a sort of hissing noise you get with a small high pressure leaky pipe)..

No engine check lights.. reset the ECU and still no check lights... Temps and oil all seem fine...

The sound itself seems to be coming from the Air intake rather than the engine itself. You can put your ear right next to the pod filter I have installed and hear it quite clearly. However when moving your ear upto the engine everything sounds reasonably fine..

Any ideas what it could be?.. From what I can tell it has to be echoing down from the air intake...

Pandoraa Contributor

Pandoraa

Posted
  • Author
Posted
hissing sound could simply be your induction sound from the pod filter.. Don't know about the grinding sound.

I have tried taking the pod filter off and just chucking a piece of cheese cloth in front of the intake.. Still get the same noise..

- also tried the above before the intake sensor.. Same

Has to be coming from further up :rofl:

G0DZLR Mentor

G0DZLR

Posted
Posted

does it change at all when you rev it or put it under load? i have a hissing sound coming from mine. happend when i put the turbo on and since after taking it off is still there. not sure what it is but theories are the injector O rings (one of them) might have a crack or something, or possibly the gasket for the intake plenum.

as for the grinding noise, what part of the motor is it coming from?

iseekool Veteran

iseekool

Posted
Posted

Depending on how long you left it, oil can sometimes separate/settle. Give it a change along with your oil filter.

If you are going to store a car for long amounts of time it is highly recommended to change all fluids before storing it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Piggaz
      Borg Warner EFR Series Turbo's V 2.0

      By Piggaz · Posted

      A few things that seem a bit off here. - why is there 2 BOV’s?  - the turbo smart BOV on the compressor housing, is it turned up ALL the way? I have seen this become an issue on old man Pete’s car. It would push open and recirc, turbo speed would rise and the boost pressure would do weird things. - stock head? Does that include springs? - tried a different MAC valve? Is it plumbed correctly?
    • GTSBoy
      Borg Warner EFR Series Turbo's V 2.0

      By GTSBoy · Posted

      Photo of manifold showing gate location? I mean, it's 6Boost, so we probably shouldn't be worrying, but always wroth knowing what the layout is. Plumbed back to atmosphere? Or into the dump?
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      Yes correct. Also, I'd avoid applying it to soft paint (however I doubt you'll ever have to deal with it in practice). So any paint that hasn't fully hardened, could be a 1k paint that never fully hardened or it could be a 2k paint that was laid down thick and hasn't yet fully hardened. 
    • kevboost7
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By kevboost7 · Posted

      Wow, i wish i found this sooner.
    • Borci88
      Borg Warner EFR Series Turbo's V 2.0

      By Borci88 · Posted

      Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
×
×
  • Create New...