Jump to content
SAU Community

Recommended Posts

bugger...your screwed then. If they have already nominated you.

I can still sign it over to someone else, i have had to go to the cop shop before and do a stat dec because they signed it over to the wrong person, i noticed on this one that it has all the stuff on the back to sign it over to someone else.

Usually if it's under a company name dont you just get with a massive fine? I think it was like 5x the norm? I'm not to sure but I know thats how my uncle gets out of them by putting all his cars under the companies name and just get ridiculous tickets, keep in mind this is in brissy

And this is not my company, the boss would not allow that, i would be happy with that if i could though.

Your boss sounds like a d*ck sorry if he's a good man be seriously, he doesn't lose out if you just pay the fine and he says he cant find the person driving the car during the time of the infringement

Company registered vehicles in Victoria have an infringement notice sent out to the company detailing the offence and requesting a nominated driver...if this notice is ignored then they send out a fine to the company with no points but much more dollars. On a typical 3 pointer speeding fine it is about $700 charged to the company. This said, if your company already nominated you then it could be too late for this without cooperation of your company. They would need to say that there was an error on their behalf in nominating you as the driver, and that given the fine happened so long ago they no longer have a log of who was driving. You've told us your company isn't the most cooperative bunch, so onto some suggestions:

Here's the important part...confirm for us that the notice has a visible mark next to "vehicle other than heavy vehicle". If this is the case, then the nominated driver may not need a truck licence to accept the points as civic compliance have identified the vehicle as light duty and therefore drivable with a car licence.

My other suggestion relates to contesting the fine itself. Given that the vehicle was a truck, you might be able to challenge the fine based on vehicle properties. I'm talking about inefficiencies in braking. It is possible you were carrying a very heavy load or that you hadn't driven this particular truck/payload for long before the incident and when you applied the brakes for the red light you knew almost straight away that you would not stop in the distance required. Instead, you maintained a safe legal speed and continued on through the intersection. This in itself is a long shot and will probably only result in a more leniant fine, but if you are going to contest it in anyway I would be focusing on this. At the least it is an argument for one's ignorance, versus one's negligence. A leniant magistrate might give you a fine with no points to preserve your licence, particularly if you plead your case that your job/family depends on it. Your driving history certainly doesn't help things.

I wish you the best of luck, but I have to say: I don't think this is the smartest place to be asking for ways to get out of an infringement. Now that you've had some input from members I'd be asking mods to delete the thread for you. Just like v8tzr should really save his triumph over the law story for the pub, because admitting that you lied to civic compliance isn't characteristic of being "older, smarter" :cool:

P.S. for interest's sake, saying you went through on a greenlight or even amber is not a valid defence. Unless the camera or sensor is faulty, the sensor is only active during a red light. There are usually two sensors, one just in front of the lines as you enter the intersection, and one on the other side of the intersection. You get snapped after going over each sensor and this is the reason ashneel received a 2 page letter with photos of his car detailing exactly how the offence was committed. The system is pretty bulletproof pending fault with the electronics. If you only go over the first sensor then you do not get a fine, even if you get snapped by the camera, because this indicates that you stopped just before entering the dangerous part of the intersection. If you go over both and have two photos taken, it shows the intent you had to carry on driving through the intersection and you will be charged. So remember, it pays to slam on the brakes even if you think you'll clear the lines by a couple of metres.

You also might want to request the service laws for the particular camera, I've heard their really slack with the servicing and apparently it states somewhere it must be serviced and tested periodically otherwise your ticket is invalid

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSP male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSP reducing bush?
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...