Jump to content
SAU Community

Nissan Gtr High Idle And Throttle Body Fix

GTRPSI

By GTRPSI,
in Tutorials / DIY / FAQ

 Share

Recommended Posts

xfixiate Rising Star

xfixiate

Posted
Posted

CRC Carbie Cleaner removes the TOMEI Throttle Coat pretty well.

Tried using it to soften, not sure it will leave the surface OK.

Took a lot of scrubbing to get the throttles completely closing.

Any suggestions/recommendations on how to apply the throttle coat CORRECTLY would be greatly appreciated. The brush in the can is too big.

xfixiate Rising Star

xfixiate

Posted
Posted

TOMEI replies to my query: Looks like clean adn try again. Im going to use a small paintbrush than the one supplied in the can. Too hard to control.

Note also that you close it to let it dry.

On 22 November 2012 20:00, Tomei Powered USA <[email protected]> wrote:

Dear John,

It sounds like you've used too much.

Depending on how you have applied it, might be best to remove it and start

again.

You only need to apply it on the edges, where the shaft makes contact with

the wall. Then on the butterfly rim edge itself, where it touches the wall,

the outer part mainly.

Go to the bottom of this page to see examples

http://www.tomei-p.co.jp/_2003web-catalogue/e193_others_gauge.html

to remove it, you can use paint thinner or acetone solution (or similar).

xfixiate Rising Star

xfixiate

Posted
Posted

I used an artist paintbrush rather than the one in the can, much easier to be precise. Throttles seal and they are now on the bump stop.

not as neat as i would like but seems to be doing the job.

MORALE: DONT CLEAN THROTTLE BODY, EVER :3some:

SiR_RB Grand Master

SiR_RB

Posted
Posted

I used the brush supplied and held the butterfly's opens while they dried

Once installed the accelerator was very not by but after afew days of driving it "wore in" and is now smooth as silk

Not to mention a perfect stable idle :)

Goodluck

Booki Rising Star

Booki

Posted
Posted

Where are you fellas getting the Tomei Throttle seal from?

Quick look on eBay/google yielded no results for aussie sellers...

That said i just cleaned my throttle bodies while doing my head gasket...doh >_<

gtr jet Veteran

gtr jet

Posted
Posted

Will cleaning the throttles affect anything else besides idle? I cleaned mine a couple of years ago when I built my motor as I thought it was carbon build up and now my car idles at 2000rpm. That doesn't really bother me though.

xfixiate Rising Star

xfixiate

Posted
Posted

Did you clean and redo the AAC valve? There is an idle adjustment screw there, plus the rebuild procedure which will also help get the idle right. I have heard of similar high idles with cleaned throttles.

If i were you I'd take the plenum off, do the throttle body goo repair, recondition the AAC valve and replace the gaskets.

If you think you have a vauumc leak, spray "Start yer Bastard" around the usual suspects. if the idle goes up, you found the leak.

If you used paper (or old) gaskets around the throttle bodies, I'd start there first.....

gtr jet Veteran

gtr jet

Posted
Posted

The engine has just been built again by a mate this time though so i'm not too sure if he's touched the aac valve. The plenum is off atm so I can replace some heater hoses so I might just have to get some of that goo for the throttle bodies.

Gaskets are new metal ones.

  • 1 year later...
  • 1 month later...
  • 6 months later...
tommis85 Mentor

tommis85

Posted
Posted

Hi,

I've giving my throttle bodies a good scrubbing too :P I shall be re-sealing and re-setting the throttle bodies as per the steps outlined above.

However, I do have a question....what do you guys do about the sealing around the butterfly shaft / spindle itself? I take it you just try to get either some moly grease into the tiny gap or a bit of the RTV silicon to cut down the gap in there?

Thanks!

Tom

  • 3 months later...
  • 5 months later...
  • 2 months later...
sic33r Enthusiast

sic33r

Posted
Posted

I had to do take the throttle bodies off twice as I done the cleaning with the carry cleaner and it made the idle worse, second time around I use tomei throttle coat and it worked a treat. Will send anywhere in Australia if somebody wants to buy

It off send me a msg 0447772496

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...