Jump to content
SAU Community

Recommended Posts

I recently added some more power to my R35, whilst it was great for simple straight line stuff (running 11.1 @ 125mph at WSID) i found that my circuit laps times have actually gone backwards (!).

My conclusion: the extra power is inducing VDC/Traction Control "events" (wheel slip) and pulling power.

Background: If you've ever forgotten to put your R35 in 'R' mode on the circuit, you will have noticed/heard/felt the system working each corner of the car, with the threshold of slip being rather pessimistic. However put the car into 'R' mode - the system then allows a higher degree of slip & yaw, less instrusive & better laps times, and more fun...

Anyway, with the aftermarket tune - say +60rwkw - 'R' mode seems like 'non-R' mode used to! (on the circuit anyway). I think the extra power is overwhelming the delicately tuned 'R' mode thresholds built into the VDC calibration.

So... consider this a heads up! Adding gobbs of power isnt going to immediately translate into quicker lap times. Unless you're comfortable turning VDC off, and driving the thing on your wits alone.

The sprint series i am in doesnt allow aftermmarket tunes, so i need to remove the tune anyway (for this coming weekend) but i thought this might spark some debate on the matter. Perhaps some others have tried adding significsant power to the R35, very interested in your thoughts (in a circuit racing context).

Edited by LSX-438
Link to comment
https://www.sau.com.au/forums/topic/286808-r35-circuit-work-and-more-power/
Share on other sites

Driver tuition is your answer to better lap times, not more power!

Driver training is probably never a bad thing, especially for amateurs like myself. But i dont think that's the primary issue here. It sure is easy/tempting to suggest that though; most people that have not driven the R35 on the track think it drives itself. That's probably true to an extent... up to about 80% of the cars potential.

That extra 10 to 20% isnt a cake walk.

Anyway, with normal power, in R mode, on the track, with RE55's, i don't feel VDC kick in, ever - unless i've made a huge error. However with (significantly) more power, it seems to break loose much more easily. Extra slip isnt necessary a bad thing, in fact i reckon a certain percetage of slip is required for the absolute quickest times (dependig on tyres). However the VDC calibration only allows so much slip. No amount of tuition is going to get around this - it's a hardware/calibration issue.

The answer is, be content with standard power OR be prepared to turn VDC (and your warranty) OFF. It's probably a non-issue, given anyone running a tune probably doesnt have a warranty anyway. This is just a heads up/fyi for R35 owners, and what to expect when you add gobbs of power :)

Edited by LSX-438

I actually noticed the increase intervantion of the stability control even with just the Midpipe added. In R mode I am getting it come in more than I did before.

I have not tracked since the mid pipe was installed however I have a day planned in about 3 weeks so I can finish of the Bridgestones before the Dunlops go on.

It is an interesting point you have raised Duncan and I am curious now.

Cheers

This is a fairly common trait in newer vehicles equiped with stability control (and importantly torque limiting protocols). Adding more power often leads to excessive interuptions, whether it be a tow vehicle or race car, and could possibly lead to a slower lap.

My suggestion would be to switch it all off.

This is a fairly common trait in newer vehicles equiped with stability control (and importantly torque limiting protocols). Adding more power often leads to excessive interuptions, whether it be a tow vehicle or race car, and could possibly lead to a slower lap.

My suggestion would be to switch it all off.

You can end up very very sideways with it switched off

Believe me I know

90 degrees to the track at Winton in the sweeper

lol, come on Jeff, you can end up sideways in anything if you fluff it up mate :woot:

We did last year's Tassie Tarmac Challenge (Rally Burnie) with it all off in some real grotty conditions and only took it off road twice ;)

Edited by Marlin

This leads me to a question i should know the answer for... when you turn VDC off, what exactly is turned off? Is it just the traction control mechnaism? What about torque split (front vs rear) and god know's whatever else is in the system?

yeah turning it off is the only answer. even in R mode with more power you will be cutting in the traction control/stability control often and it will slow your times.

I have driven standard R35 on track and upgraded (exhaust, ecu etc) and prefer VDC to OFF. yes you will find yourself dealing with some power oversteer but its very controlable if you know how to use throttle and opposite lock (and I'm sure you do mate).

it's not like it becomes a scary unbalanced car when you turn VDC off. the chassis is great, it still has loads of grip and the active torque split is still working as it should. just no traction control will cut in no matter how sideways you get it. but I honestly reckon you would have to actually try to spin one off the track. they are very controlable in a slide and you can easily balance the car on the throttle. and it's fun. :woot:

Its one thing to sit here and tell you how to drive....but from what I know you already have more than a good handle on that.

The answer lays in something else, and thats the ability of the turbocharger system of the GTR to unbalance the car. If you stand on the throttle at the wrong point of the corner in a GTR its easy to unbalance the car, even slightly step the tail out, and lose time. VDC-R isnt so much the problem, but the ability of the car to change direction and correct for a rapid shift in lateral G-Force really is! The key is to be as smooth and progressive as possible, with the fastest lap times coming to the calmest driver :banana:

This is why when I custom tune a GTR for the track I do this -

customtune.jpg

Notice that the boost curve progressively pulls away from stock and then only by a psi or so from 4200 (thats over an off the shelf Stage II Cobb tune). The key to giving a GTR more power AND improving lap times is by minimising the throttle-on imbalance of the car and keeping the power curve as linear and 'spike free' as possible. This is difficult with an airflow based wastegate duty cycle table (as the GTR has from the factory), so we spend many hours developing wastegate control maps that keep boost spikes out of full throttle upshift and keep the GTR balanced on the exit and transition :(

This is not saying the way anyone else does it is wrong. There are some out there in Aus that seem to have a good handle on the GTR and reflashing. Just this way is how we do it after spending a few hundred laps trying different things in our own R35 :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Will have a look at that. I cant see any leaks 
    • Put another overflow bottle (ie, a 1.25 coke bottle or similar) under the overflow hose and see if it is being pushed out there or if it is disappearing into the engine.
    • Staring on a stand is no issue. You just have to wire everything up, give it fuel and cross your fingers that the stand is robust enough. Arranging the inlet plumbing is often the hardest part, without any surrounding structure to hand some of it from. No need for coolant if you only want to run it for <1 minute. As to the gearbox - I think the little Aisin box is a bit stronger than the other small Nissan boxes that went behind SRs, but I wouldn't be too keen to test its limits with the torque of a boosted 25. I don't know if you can retain the box and the tailshaft. The box won't connect to the RB without an adapter of some sort, which is either a plate that will push the engine forward (which is not good for fitting it into the bay's available space) or push the box back, which messes with the box position and tailshaft length - OR - cut and shut work on the bellhousing, which is a long way from "least modification". I'd be buying a new 370Z 6 speed or similar, doing what has to be done to that to make it fit RB (ie, cut and shut bellhousing) and the requisite tailshaft custom/mods.
    • Hi Everyone I am from West Pennant Hills in NSW. Been too busy until recently to attend to my RB25DET Series 2 engine until recently. I am planning to stick it into the S15 shell at this stage, unless a nice SR20DET turns up... For now, i am going to try and get the RB25 running and working well then decide what gearbox to use. My preference is to retain the SR20DET  6 speed gearbox and tail shaft to retain as much and least modifications as i can avoid. I am an old guy and won't be doing any heavy drifting so i don't need a bullet proof gearbox Does anyone have experience with starting the RB on a stand? I got everything setup as much as I can with the info i can find... endless searching and videos on Youtube I would be great to get some pointers Cheers Songo
    • Hey all, Recently have had my s1 r33 gtr serviced and noticed my coolant reservoir was topped up to the max line. Took the car out for 1 yesterday and noticed today the reservoir is completely empty.  Any ideas? Radiator is full
×
×
  • Create New...