Jump to content
SAU Community

Recommended Posts

If you change your mind.

I have hks2530s on a stock manifold and im upgrading to a motec m800 and im looking for the hardpipe kit from turbo to airfilters off the turbos.

Do the turbos sit in the same place as a stock manifold would? i have mines stainless dump pipes off the turbos to a split veilside 2.5 inch front pipes to cat.

Intrested in the manifolds and hard pipes to turbos afmless.

Did you mount your bovs turbo side or use the stock pipe work and placement of the gtr bovs.

Let me know either way mate id even be intrested in a trade of stock manifolds/heatshields if you wanted to do it that ways plus cash your way.

Edited by Gtir-keiron
If you change your mind.

I have hks2530s on a stock manifold and im upgrading to a motec m800 and im looking for the hardpipe kit from turbo to airfilters off the turbos.

Do the turbos sit in the same place as a stock manifold would? i have mines stainless dump pipes off the turbos to a split veilside 2.5 inch front pipes to cat.

Intrested in the manifolds and hard pipes to turbos afmless.

Did you mount your bovs turbo side or use the stock pipe work and placement of the gtr bovs.

Let me know either way mate id even be intrested in a trade of stock manifolds/heatshields if you wanted to do it that ways plus cash your way.

hey mate, nah im not gona seperate the manifolds, ive already got buyers for for the turbos, hard pipe kit, dumps and front pipe.

i just gota wait till i pick them up during the week and meet up with all the buyers. if anything changes ill be in touch but everything seems to be gone atm

hey mate, nah im not gona seperate the manifolds, ive already got buyers for for the turbos, hard pipe kit, dumps and front pipe.

i just gota wait till i pick them up during the week and meet up with all the buyers. if anything changes ill be in touch but everything seems to be gone atm

Did this stuff sell mate im still keen as bro.

Just pulled my motor out for a clean up of the engine bay.

Let me know mate

!!!!!!!!!!!!!!!!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok so after much research and talking with knowledgeable people I've got my turbo conversion done and it's all running great other than 1 small issue.  Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd. But nothing drive or what gear your in when you pop it into tiptronic.  I'm sure there is may e 1 wire in the ecu plug I need to move to rectify this. Dose anyone here have any ideas?   Cheers guys
    • Sorry I haven't been following all the detail, so you may have tried this. Does it idle with the tiniest bit of throttle you can add? You've mentioned the IACV, does it have an AAC valve and have you adjusted it at all (ie, screw the idle adjust screw all the way in, then back it out a couple of turns until idle is stable)?
    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
×
×
  • Create New...