Jump to content
SAU Community

Recommended Posts

Hi guys,

I remember seeing a post on here somewhere about this but I can't seem to find it- if someone can point me in the right direction I would appreciate it.

Wondering if anyone has run an R32 actuator (10psi) with the stock R33 boost solenoid earthed out and ended up with a stable 12psi?

Any experiences would be great.

Cheers

Chris

Edited by Yeedogga
Link to comment
https://www.sau.com.au/forums/topic/288200-quick-boost-solenoid-question/
Share on other sites

Yeah thats the kinda boost you'll be expecting with the r32 actuator. Did the same thing on my 33 except I just ditched the boost control solenoid completely instead of earthing it. Switching from my standard actuator to the r32 item put boost from around 8 psi up to around 11psi, this was with a front mount cooler and full 3" exhaust. I wouldn't want to push the stock turbo past 12 psi just to make sure you're not stressing the ceramic exhaust wheel too much.

Thanks for the replies guys, but i should have been a bit clearer - I'm already running an R32 actuator and getting a rock solid 10psi at the moment with a FMIC/exhaust.

I was hoping to use the stock boost solenoid to switch between 10psi and 12psi. I don't want to run 12psi all the time but it would be good to have the car remapped on 12psi and then use that setting for when I need a bit more oomph.

I think if you have the boost control solenoid operating it will start off runnin 5 psi until 4500 rpm and then the rating of the actuator, r33 being 7psi and r32 10psi from 4500rpm upwards. And the low boost setting isn't adjustable.

Correct me if i'm wrong if anyone has tried this?

Well the low boost setting will be 10psi with the R32 actuator- regardless of whether the electronic solenoid is connected or not.

What I'm hoping to do is get the R33 solenoid to bleed off 2psi when it is earthed, giving me 12psi.

I guess I'll just have to try it out!!

Cheers

  • 3 months later...

if you run the r32 actuator, then you dont need the solenoid, it's pointless

the r32 actuator will give you a prefect 12psi, whichi is about the max i would run on the r33 turbo

here are the spec of the std actuators

Use the air gun to blow compressed air approx A ~ B kgcm2 into the hose and make sure the swing valve controller rod operates.

where

HR32 - A = 0.8 and B = 0.9 kgcm2 which is 0.85kgcm2 (average) which is 12.08 psi

BNR32 A = 0.7 and B = 0.8kgmc2 which is 0.75kgcm2 (average) which is 10.66 psi

ECR33 manual is 385mmhg which is 7.4446 psi

ECR33 auto is 270mmhg which is 5.220 psi

BCNR33 A = 0.79kgcm2 and B = 0.85kgc2m which is 0.82kgcm2 (average) which is 11.6 psi

if someone can find ER34/BNR34 please let me know

cheers for that Paul :wub: i always thought the r32 actuator was rated to 10psi, i guess 12 won't be too bad.

i have just unplugged the solenoid and am going to hide the dangling plug bit under the airbox so it all looks nice and stock, easier than pulling everything out and blocking off hoses etc i think.

EDIT: in the process of taking out my current actuator.. can anyone point me in the right direction re: removing the pin at the turbo end? i don't want to damage anything.

thanks

can anyone help me? sorry to be a pain :wub:

it looks like the rod is sort of clipped onto the turbine housing, reading around on other site it says to 'pop' this bit off.. but i'm a bit too cautious for that!

  • 1 month later...

on a very quick short / run it might be ok

but after repeated loading up the stock core will be useless and wont perform

the end results would be excessive intake temps causing detonation

r32 actuator with no boost control solenoid = 10psi

r32 actuator with boost control solenoid hooked up normal = 10psi and at 4500 rpm 12psi

r32 actuator with boost control solenoid hooked up and earthed out = 12psi

Edited by MrR33666

no, that's incorrect

from the nissan service manual;

HR32 - A = 0.8 and B = 0.9 kgcm2 which is 0.85kgcm2 (average) which is 12.08 psi

so the minimum boost you can run when using the R32 actuator is 12psi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...