Jump to content
SAU Community

Recommended Posts

Hi guys,

I remember seeing a post on here somewhere about this but I can't seem to find it- if someone can point me in the right direction I would appreciate it.

Wondering if anyone has run an R32 actuator (10psi) with the stock R33 boost solenoid earthed out and ended up with a stable 12psi?

Any experiences would be great.

Cheers

Chris

Edited by Yeedogga
Link to comment
https://www.sau.com.au/forums/topic/288200-quick-boost-solenoid-question/
Share on other sites

Yeah thats the kinda boost you'll be expecting with the r32 actuator. Did the same thing on my 33 except I just ditched the boost control solenoid completely instead of earthing it. Switching from my standard actuator to the r32 item put boost from around 8 psi up to around 11psi, this was with a front mount cooler and full 3" exhaust. I wouldn't want to push the stock turbo past 12 psi just to make sure you're not stressing the ceramic exhaust wheel too much.

Thanks for the replies guys, but i should have been a bit clearer - I'm already running an R32 actuator and getting a rock solid 10psi at the moment with a FMIC/exhaust.

I was hoping to use the stock boost solenoid to switch between 10psi and 12psi. I don't want to run 12psi all the time but it would be good to have the car remapped on 12psi and then use that setting for when I need a bit more oomph.

I think if you have the boost control solenoid operating it will start off runnin 5 psi until 4500 rpm and then the rating of the actuator, r33 being 7psi and r32 10psi from 4500rpm upwards. And the low boost setting isn't adjustable.

Correct me if i'm wrong if anyone has tried this?

Well the low boost setting will be 10psi with the R32 actuator- regardless of whether the electronic solenoid is connected or not.

What I'm hoping to do is get the R33 solenoid to bleed off 2psi when it is earthed, giving me 12psi.

I guess I'll just have to try it out!!

Cheers

  • 3 months later...

if you run the r32 actuator, then you dont need the solenoid, it's pointless

the r32 actuator will give you a prefect 12psi, whichi is about the max i would run on the r33 turbo

here are the spec of the std actuators

Use the air gun to blow compressed air approx A ~ B kgcm2 into the hose and make sure the swing valve controller rod operates.

where

HR32 - A = 0.8 and B = 0.9 kgcm2 which is 0.85kgcm2 (average) which is 12.08 psi

BNR32 A = 0.7 and B = 0.8kgmc2 which is 0.75kgcm2 (average) which is 10.66 psi

ECR33 manual is 385mmhg which is 7.4446 psi

ECR33 auto is 270mmhg which is 5.220 psi

BCNR33 A = 0.79kgcm2 and B = 0.85kgc2m which is 0.82kgcm2 (average) which is 11.6 psi

if someone can find ER34/BNR34 please let me know

cheers for that Paul :wub: i always thought the r32 actuator was rated to 10psi, i guess 12 won't be too bad.

i have just unplugged the solenoid and am going to hide the dangling plug bit under the airbox so it all looks nice and stock, easier than pulling everything out and blocking off hoses etc i think.

EDIT: in the process of taking out my current actuator.. can anyone point me in the right direction re: removing the pin at the turbo end? i don't want to damage anything.

thanks

can anyone help me? sorry to be a pain :wub:

it looks like the rod is sort of clipped onto the turbine housing, reading around on other site it says to 'pop' this bit off.. but i'm a bit too cautious for that!

  • 1 month later...

on a very quick short / run it might be ok

but after repeated loading up the stock core will be useless and wont perform

the end results would be excessive intake temps causing detonation

r32 actuator with no boost control solenoid = 10psi

r32 actuator with boost control solenoid hooked up normal = 10psi and at 4500 rpm 12psi

r32 actuator with boost control solenoid hooked up and earthed out = 12psi

Edited by MrR33666

no, that's incorrect

from the nissan service manual;

HR32 - A = 0.8 and B = 0.9 kgcm2 which is 0.85kgcm2 (average) which is 12.08 psi

so the minimum boost you can run when using the R32 actuator is 12psi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...