Jump to content
SAU Community

Recommended Posts

Hi guys,

I remember seeing a post on here somewhere about this but I can't seem to find it- if someone can point me in the right direction I would appreciate it.

Wondering if anyone has run an R32 actuator (10psi) with the stock R33 boost solenoid earthed out and ended up with a stable 12psi?

Any experiences would be great.

Cheers

Chris

Edited by Yeedogga
Link to comment
https://www.sau.com.au/forums/topic/288200-quick-boost-solenoid-question/
Share on other sites

Yeah thats the kinda boost you'll be expecting with the r32 actuator. Did the same thing on my 33 except I just ditched the boost control solenoid completely instead of earthing it. Switching from my standard actuator to the r32 item put boost from around 8 psi up to around 11psi, this was with a front mount cooler and full 3" exhaust. I wouldn't want to push the stock turbo past 12 psi just to make sure you're not stressing the ceramic exhaust wheel too much.

Thanks for the replies guys, but i should have been a bit clearer - I'm already running an R32 actuator and getting a rock solid 10psi at the moment with a FMIC/exhaust.

I was hoping to use the stock boost solenoid to switch between 10psi and 12psi. I don't want to run 12psi all the time but it would be good to have the car remapped on 12psi and then use that setting for when I need a bit more oomph.

I think if you have the boost control solenoid operating it will start off runnin 5 psi until 4500 rpm and then the rating of the actuator, r33 being 7psi and r32 10psi from 4500rpm upwards. And the low boost setting isn't adjustable.

Correct me if i'm wrong if anyone has tried this?

Well the low boost setting will be 10psi with the R32 actuator- regardless of whether the electronic solenoid is connected or not.

What I'm hoping to do is get the R33 solenoid to bleed off 2psi when it is earthed, giving me 12psi.

I guess I'll just have to try it out!!

Cheers

  • 3 months later...

if you run the r32 actuator, then you dont need the solenoid, it's pointless

the r32 actuator will give you a prefect 12psi, whichi is about the max i would run on the r33 turbo

here are the spec of the std actuators

Use the air gun to blow compressed air approx A ~ B kgcm2 into the hose and make sure the swing valve controller rod operates.

where

HR32 - A = 0.8 and B = 0.9 kgcm2 which is 0.85kgcm2 (average) which is 12.08 psi

BNR32 A = 0.7 and B = 0.8kgmc2 which is 0.75kgcm2 (average) which is 10.66 psi

ECR33 manual is 385mmhg which is 7.4446 psi

ECR33 auto is 270mmhg which is 5.220 psi

BCNR33 A = 0.79kgcm2 and B = 0.85kgc2m which is 0.82kgcm2 (average) which is 11.6 psi

if someone can find ER34/BNR34 please let me know

cheers for that Paul :wub: i always thought the r32 actuator was rated to 10psi, i guess 12 won't be too bad.

i have just unplugged the solenoid and am going to hide the dangling plug bit under the airbox so it all looks nice and stock, easier than pulling everything out and blocking off hoses etc i think.

EDIT: in the process of taking out my current actuator.. can anyone point me in the right direction re: removing the pin at the turbo end? i don't want to damage anything.

thanks

can anyone help me? sorry to be a pain :wub:

it looks like the rod is sort of clipped onto the turbine housing, reading around on other site it says to 'pop' this bit off.. but i'm a bit too cautious for that!

  • 1 month later...

on a very quick short / run it might be ok

but after repeated loading up the stock core will be useless and wont perform

the end results would be excessive intake temps causing detonation

r32 actuator with no boost control solenoid = 10psi

r32 actuator with boost control solenoid hooked up normal = 10psi and at 4500 rpm 12psi

r32 actuator with boost control solenoid hooked up and earthed out = 12psi

Edited by MrR33666

no, that's incorrect

from the nissan service manual;

HR32 - A = 0.8 and B = 0.9 kgcm2 which is 0.85kgcm2 (average) which is 12.08 psi

so the minimum boost you can run when using the R32 actuator is 12psi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...