Jump to content
SAU Community

Recommended Posts

just sat my 25/30 in my 32 and the intake manifold i've got wont fit with the clutch line where it is. The line on mine comes out of the bottom of the cylinder, if it come out the side would probably be fine( though couldn't hurt if the cylinder was slightly shorter). The picture on the just jap web site of the hcr32/cefiro one has the line coming out the side, can anyone tell me if it does? and what about the r33 cylinder? is it longer or shorter than the 32 and does the fluid line come out the side or bottom? would it fit the in 32 easily. will be running a 25 slave cylinder if that matters. Any info is much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/289589-clutch-cylinder-for-32/
Share on other sites

I've had similar problems, but used a different plenum (CPC).

S14 and R31(aus) have the line out the side.

Pic is of r31 relocated higher.

http://i223.photobucket.com/albums/dd81/30...ster-cleara.jpg

more pics here http://s223.photobucket.com/albums/dd81/30det/

R33 GTSt master cylinder is shorter than 32 and I think the line comes out the bottom (can check if needed).

I got one thinking my plenum wasn't going to clear (as matey had problems with his GREddy plenum) but my custom GTR plenum didn't foul.

thanks guys. I'll mesure up and see if the r33 20mm shorter will work( i've got a 25 box so will keep master, slave the same as factory). Also checked a mates s13 and was same cylinder diameter (5/8) was shorter than mine and the line was coming out the side.

  • 2 months later...

Thanks all ,i just did this works in a R31 aswell RB30DET with redrilled/elongated engine mount brackets holes drivers side by 15mm lower ,passenger bolt holes elongated by half a hole is all it would go.

I took turbo side engine mount bracket (4 bolts off) then plenum Greddy copy just fitted past clutch master cylinder from r33.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If it (the code) wasn't still current, it should have gone away by itself by now. No, nothing it 10/10. But it is quite likely. Everything else to do with the ignition could still be responsible (which is wires and connectors). The car is an old piece of shit now, so all the wires and connectors are also old pieces of shit.
    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
×
×
  • Create New...