Jump to content
SAU Community

Recommended Posts

That looks like a great build!

Its a massive shame its in sweedish, becahuse there looks like there is a huge amount of information there that seems interesting and quite helpful too!

Just a couple of questions,

Whats the car going to be used for?

And why stick with the CA and not go SR?.. I suppose less poeple run CA's so its a little more different..

Yes, you are right. There is a lot of information about how to rebuild gearboxes, upgrade the brakes, engine tuning, chassis tuning and so on. The information I put up here is just a short pick of it.

I use the car mainly on the street and from time to time on tracks and 1/4 mile. It is great fun. When I lived down in France, I once took it to Monaco and drove slowly by the Casino. It got more attention than many of the Fers, Lambos and Bentleys. I like! :(

The Ca is capable of a lot of power when tuned correctly. My earlier aim was 600BHP but now I am increasing it up to some +700BHP. Most of the SR's here in Sweden end at some 500BHP and that engine has a lot to wish for when it comes to its factory internals (as an example, I am no friend of the SR head and its twin lifter cam lobes).

The CA has also things that need improvement. The crank is forged and ok but the pistons doesn't last when reaching +300BHP. The Rods give in at about +400BHP and the oil cooling suck.

So...I did lots of hardware tuning to make a massive improvement on the CA's durability and many other tweaks to get it up in power.

700HP!?!?!?!?!?!

out of a CA!?

How often do you intend on rebuilding it!?

It is not a question about rebuilding. It is all about doing it the right way from the beginning (using high grade components) and keeping a high level of normal service (oils, filters etc).

This is how I rebuilt a Z32 gearbox to fit my car (200sx S13 with ca18det).

The good thing about it is that you can reuse the nice clutch you already invested in for your S13. I have a twin disc OS Giken clutch, bought for my S13 gearbox. Both gearboxes have the same dimensions on the ingoing splined shaft, release bearing, sleave etc. This makes it an absolute fit. The gear ratio is slightly higher. My car had before a top speed of 282km/h at 7800rpm. With the ratio of the Z32 gearbox and new tyres it will make aprox. 305km/h. Hope you like it.

Clutch: Same as S13 (clutch, bearing, release sleave, starter motor, flywheel)

Weight: A bit heavier because of internal dimensions

Length: A bit shorter (reuse the yoke from the Z32 and the rear part from theS13 and make a new, longer prop shaft)

Gear ratio: A bit higher (~5%)

Shift stick: Reuse the one from Z32 or buy a new short shift

Welding in cast aluminium: You need a TIG or go to a welding shop (sand blast the weld area to make it clean and easier to weld)

Z32 original gearbox from a Twin Turbo 1994

img45ca2ea7a58de.jpg

img45ca2eada2b6f.jpg

img45ca2eb353b32.jpg

Disassemble the clutch housing (Z32)

img45ca2df5ccd53.jpg

Parts to remove to disassemble the clutch housing. Not shown are the screws on the outside (remove), attaching the cluth housing to the gearbox.

img45ca2df73b588.jpg

Remove all screws around the cover and carefully lift it off

img45ca2df75f7b4.jpg

Remove both snap rings and the stopper ring

img45ca2df603a9e.jpg

Be careful not to lose any important washers or shims

img45ca2df72cb27.jpg

Important! First remove the screw, spring and ball before removing the complete interlock assembly, the ball might fall into the gearbox.

img45ca2df6b27a7.jpg

Before you disassemble the clutch housing of the S13 gearbox, you have to make a centering device. Use a plexi glass plate (10mm) and drill a 16mm hole in the centre, put the plate over the shaft (snug fit) and carefully drill 4 small holes exactly in the centre of the holes where the gearbox is attached to the motor. Remove the plate and carefully drill the holes just as big to get the screws in

img45ca2df79149e.jpg

Result

img45ca2df7a4d24.jpg

Remove the clutch housing from the ca18det S13 gearbox. It is more or less just to remove the screws on the outside of the clutch housing, remove the cover and one snap ring.

img45ca2df7b56c8.jpg

Remove the snap ring under the cover

img45ca2df5e4457.jpg

Comparision between the both gearboxes. One is useless over 350-400Bhp, the other last well over 1000Bhp and more.

img45ca2df77bcd7.jpg

Use an angle cutting machine and cut off the flange from the S13 gearbox ca. 50mm, take it to a machine shop and have it grinded down to 45mm. Important to get it absolutely flat and equal all around.

img45ca2df64edd1.jpg

Use an angle cutting machine and cut off the flange from the Z32 gearbox ca. 40mm, throw away the flange and take the rest of the clutch housing to a machine shop and have it grinded down to 355mm. Important to get it absolutely flat and equal all around.

img45ca2df6cdd30.jpg

Both parts after grinding, cleaning and reattaching the clutch housing on the Z32 gearbox

img45ca2df79149e.jpg

Put the S13 flange snug to the Z32 clutch housing and attach the centering plate with four screws

img45ca2df554b53.jpg

Side view

img45ca2df71929e.jpg

Top view. Important to align and rotate them like on the picture

If you do not own a TIG-welding machine, you go to the machine shop again and have it carefully welded together, both from the outside and the inside

img483da0680add2.jpg

img45ca2df6664d9.jpg

Reuse the shift stick bracket from the Z32 gearbox. You have to cut out some small triangles from it, bend it to a Z-shape to fit the S13 under body and then weld the cut outs together. (borrowed picture)

img45ca2df704a7b.jpg

The new short shift

img45ca2df7c606e.jpg

A small change of shift stick position compared to the original (borrowed picture)

img45ca2df6a6c29.jpg

A plate to cover the hole at the shift stick (borrowed picture)

img45ca2df678dbb.jpg

A bracket to hold the gearbox in place (borrowed picture)

img45ca2df62dac6.jpg

Aligning the gearbox with the rear axle. Put a steel tube in the gearbox, aim it towards the centre of the rear axle flange and find the final position of the gearbox bracket. (borrowed picture)

img45ca2df61a201.jpg

Side view (borrowed picture)

img45ca2df74bf2f.jpg

Front view (borrowed picture)

img45ca2df76f1b7.jpg

The prop shaft. Mount the Z32 yoke in the gearbox and the original flange on the rear axle. Measure the centre distance between the loops in the yoke and in the rear flange. Use this measure and go to your local prop shaft supplier and have him to make your new prop shaft. The shaft rotate at about 10.000rpm at max speed so it has to be dimensioned for the forces and also balanced.

  • 2 weeks later...

Device to correct the speedometer. Needed because of the different speed signals and gear ratio in the Z32 gearbox. It also handle changed wheel/tyre sizes etc. The sensor signal to the speedometer is handled to show the correct speed on the speedo. It also show the max speed from the latest run by pressing a button.

img4af272e1b4be2.jpg

  • 3 weeks later...

Today I picked up the new turbo from Logo31-3.gif.

Without doubt they are skilled experts in the world of turbos. Dick has made an excellent job. There is nothing about this SX700S that is standard. Top Class Dick! 1000 cheers!

img4b0ec4783f16c.jpg

img4b0ec4766eeae.jpg

img4b0ec476a59b4.jpg

img4b0ec476cab7b.jpg

img4b0ec476f2c21.jpg

img4b0ec47723bab.jpg

img4b0ec477671d8.jpg

img4b0ec4778c39f.jpg

img4b0ec477b1567.jpg

img4b0ec477d6731.jpg

img4b0ec47818ff7.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...