Jump to content
SAU Community

Nissan Cefiro - 4 Door Love!

konect
 Share

Recommended Posts

konect Mentor

konect

Posted
Posted (edited)

Going to chuck my car up for sale as I don't really get to use it these days. I have only owned this car for a year and have had it registered since February this year (this was new rego and the car went through the VicRoads inspection).

I am looking for $13,500 with the Final Konnexion kit or $13,000 with out and made it negotiable however I'm not going to sway too much from the set price so please refrain from low balling :mrt:

Mods:

EXTERIOR:

CA31 Chassis - July 1989 Build

Manual conversion

Final Konnexion Body Kit - Genuine Kit - Only kit of its kind in Australia! - Not currently fitted

M-Sports 30mm Flared & Vented Front Fenders - Genuine

Rear Guards Flared by 20mm

Full Respray in factory Diamond Black

Factory Sunroof

Late Model Tail Lights

Kaixon 6000k HID Headlight Kit

Legal Tint with Front Banner

Notes:

Bodykit was drifted by the guy I bought it off and is in good condition except for the rear passenger skirt but is an easy fix, just needs some glassing.

Drivers door has a scratch from when the front bar came off.

Small blemishes but otherwise excellent condition.

ENGINE:

RB20DET - Recently changed over after Bee*R limited destroyed a piston (FYI - Bee*R limted was not refitted :) )

HKS GT2835 Ball Bearing Turbo Kit (highflowed) ONLY 2500km since rebuild! (Went bang with old motor)

HKS Tuned Length Stainless Highmount Manifold

HKS 50mm Race Gate (1 Bar spring installed, other springs come with it)

Xtreme Chrome Moly 5.5kg Flywheel

Xtreme 9 Puck 25% Over Standard Clutch

SplitFire Coil Pack Kit

R32 GTR Coilpack Loom

Braided Lines where necessary, Fire Retardant Shields on All other Lines

3" Dump Pipe w/ Heatwrap

3" Turbo Back Exhaust.

East Bear GTR Cooler Kit & Piping

Custom Stainless Intake Cross Pipe (By C-red Tuning)

R33 GTR VSpec Intercooler (painted black)

Trust 10 Row Oil Cooler w/ Braided Lines & Spin on Adaptor (painted black)

Bosch O40 Fuel Pump with Source Power direct from Battery

New rocker cover gasket (2000ks old)

Nissan Steel Exhaust Header Gasket w/ new Nissan Studs and Brass Nuts

Quality Blue Silicon Used on all joins and bends

Silicon Vacuum Hoses

Silicon Radiator Hoses

Razor Grounding Kit

Oil Catch Can

Retuned Standard ECU - Socketed ROM (in Japan)

Had car dynoed recently and made 192rwkw on stock boost. Needs about 1.2bar to make serious power.

DRIVETRAIN:

2-Way Mechanical Diff (Nice and quiet)

Gearbox Had 6 Bearings Replaced (Synchros are crunchy which 'may' be caused by slave cylinders not opening fully)

R32 Half Shafts installed

HPI Braided Clutch Line

Brand New Speedo Cable

UNDERNEATH:

Tein HA Coilovers (Purchased brand new in 04, 35,000km old now with no leaks or clunks)

Tein Castor Rods

Castor Rod Mount Brace

Cusco Front Strut Brace

Adjustable Traction Rods in Rear

Adjustable Upper Arms in Rear

HICAS Lock Back

Drift Pineapples on Rear Cradle

Work Emotion Kai 17 x 9 +17 all round

Brand new Falken 452 on the front and brand new tires on rear (215's all round)

Full 5 Stud Conversion, R32 Rear & Custom Billet Front Hubs

New rotors and pads all round (2000 ks old)

20mm 5 Stud Bolt on Hub Centric Spacers on Front

Z32 4 Pot Brakes & R32 2 Pot Rears in Red (replaced Rear Brake Lines)

S14 Steering Rack & Custom Power Steering Lines

INTERIOR:

Sexual dash mat (extremely rare!)

HKS EVC3 Boost Controller

Greddy Boost Guage

Nardi Turino Steering Wheel

Will come with standard drivers seat (NOT Zeta as pictured)

Stock S13 (Passenger)

Razo Gearknob

Pioneer MP3 Head Unit

Pioneer 6" Splits

That's the gist of it I think. Only been drifted a few times and has heaps of potential to make big power (est at around 250 rwkw with a tune and the parts I haven't put on yet)

Car is fully complied and VIN plate fitted. Currently has 6 months rego so will be a lovely slider/sleeper for anyone who is keen.

I can be contacted on 0412 033 449 for interested buyers.

PICS:

Before new rims and lowering -

P6210253small.jpg

P9040283small.jpg

P9040284small.jpg

After new rims and more low (current state) -

P9260355small.jpg

P9260356.JPG

P9260358small.jpg

P9260361small.jpg

P9260362small.jpg

P3140026small.jpg

Edited by konect
Link to comment
https://www.sau.com.au/forums/topic/291106-nissan-cefiro-4-door-love/
Share on other sites
konect Mentor

konect

Posted
  • Author
Posted
no rear bar?

whats with the tape on the left tail-light?

Lol check my posts for the rear bar story, having some serious issues getting one in Vic :P

Tape on the left light covers a little hole in it. Been on there since I bought it and does the job well!

konect Mentor

konect

Posted
  • Author
Posted (edited)

Hey Rory,

Just after cash atm :ermm:

************************

Also, car is now located in Diamond Creek (NE Melb suburbs)

Edited by konect
erik Community Regular

erik

Posted
Posted
Lol check my posts for the rear bar story, having some serious issues getting one in Vic :P

Tape on the left light covers a little hole in it. Been on there since I bought it and does the job well!

fair enough, it looks nice

Interior pics?

would r33 front seats fit?

konect Mentor

konect

Posted
  • Author
Posted
fair enough, it looks nice

Interior pics?

would r33 front seats fit?

I didn't post interior pics because it has the wrong seats in it still. I'm going to swap them out this weekend hopefully and then take some pics :)

R33 seats will bolt in 3/4 bolts but you have to adjust the 4th one. Currently it has an S13 passenger seat which is bolted in but needs the 4th one modded.

erik Community Regular

erik

Posted
Posted
I didn't post interior pics because it has the wrong seats in it still. I'm going to swap them out this weekend hopefully and then take some pics :)

R33 seats will bolt in 3/4 bolts but you have to adjust the 4th one. Currently it has an S13 passenger seat which is bolted in but needs the 4th one modded.

fair enough, i'm interested i just need to sort out a loan,

i have r33 front seats thats why i was wondering, couldn't i just put them on like cefiro rails?

konect Mentor

konect

Posted
  • Author
Posted (edited)
fair enough, i'm interested i just need to sort out a loan,

i have r33 front seats thats why i was wondering, couldn't i just put them on like cefiro rails?

Ah no worries, let me know how it goes.

You probly could wog it up to go on ceffy rails but would be easier to mod the 4th bolt as you just have to cut a bit off and weld a loop on because the end of the bracket covers half the hole so couldn't drill it. That will make no sense unless you actually see it lol

Edited by konect
erik Community Regular

erik

Posted
Posted
Ah no worries, let me know how it goes.

You probly could wog it up to go on ceffy rails but would be easier to mod the 4th bolt as you just have to cut a bit off and weld a loop on because the end of the bracket covers half the hole so couldn't drill it. That will make no sense unless you actually see it lol

haha your right there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      New kid on the block

      By GTSBoy · Posted

      The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Duncan
      New kid on the block

      By Duncan · Posted

      Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • iain_ST44GA
      M35 VQ25DET starter motor

      By iain_ST44GA · Posted

      Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • Murray_Calavera
      R33 GTR running -9 with no tune

      By Murray_Calavera · Posted

      I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...