Jump to content
SAU Community

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

think i need to clean the rubber off the Ceffy and you can see where i gave the tyre's a tap coming onto the start/finish straight, fair lucky not to lose the rear bar.

post-51334-1267607023_thumb.jpg

Edited by DSTROY
Gtr as a daily 34 as a project.

theres several interesting 32 gtrs on carsales atm

one is #78 of the original aussie delivered 100

one is a tommy kaira spec 32

and another has only 9800km on the clock...

whats ur budget? :D

-D

theres several interesting 32 gtrs on carsales atm

one is #78 of the original aussie delivered 100

one is a tommy kaira spec 32

and another has only 9800km on the clock...

whats ur budget? :D

-D

I so wouldnt mind that TK R32 GTR... but its so ugly and not in my favourable colour.

Excessive lowering will give you too much toe in, unless you have adjutable upper arms

stock suspension now and stock arms

only adjustables that were in it were coilovers and rear camber arms

will have to put hicas back in

could that be the problem?

think i need to clean the rubber off the Ceffy and you can see where i gave the tyre's a tap coming onto the start/finish straight, fair lucky not to lose the rear bar.

Proves that you are driving it properly!

stock suspension now and stock arms

only adjustables that were in it were coilovers and rear camber arms

will have to put hicas back in

could that be the problem?

it can affect hicas if the toe is greater than 2' on either side, the hicas computer senses it somehow and disables hicas after about 15 minutes

for what its worth, i got some rear adjustable upper control arms last year for around $350 and the precise adjustment that the aligner was able to make more than justifies the cost... makes the car perform much better with less tyre wear to boot ;D

not regency friendly, but theyre easy enough to get engineered

-D

it can affect hicas if the toe is greater than 2' on either side, the hicas computer senses it somehow and disables hicas after about 15 minutes

for what its worth, i got some rear adjustable upper control arms last year for around $350 and the precise adjustment that the aligner was able to make more than justifies the cost... makes the car perform much better with less tyre wear to boot ;D

not regency friendly, but theyre easy enough to get engineered

-D

i think you'll find what ive had to remove :D

photo2ms.jpg

Is that all?

*sigh* its enough to throw his geometry all out of wack again

he has the front castor arms, the rear camber arms, the adjustable suspension... all 3 things that work in tandem to ensure the suspension actually works properly

u should enquire about getting that stuff engineered man, rory thompson does it for $500 odd if I recall correctly, and that mean you could continue using the control arms for caster/camber... not the suspension but eh, 2/3 is better than nowt

-D

Yeah my suspension was out of whack when I removed everything for regency, handled like a bucket of shit on the way to Tyre Power for an alignment which straightened everything out and made it feel perfect again afterwards.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
    • I just stack 2 pieces of 200x50 timber on top of each other. Total length about 900mm, with the top one being a little shorter and both having a 45° angle cut on them to make the front edge a bit of a ramp. Put these in front of each front wheel, drive up on them, throw the trolley jack under. Takes 1 minute. Scissor jacks can eat a bowl of dicks. I never use on under my car unless desperate.
×
×
  • Create New...