Jump to content
SAU Community

The Sa Wasteland

heslo

By heslo,
in South Australia

 Share

Recommended Posts

  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Dohmar Grand Master

Dohmar

Posted
Posted
man, just putting a wheel back on ruins me (knees)... certainly with the cold weather.

nasty stuff with no patella's

got all this stuff on the go with the r32 rb26 but cant muster the will in my knees to do anything.

so so need a car hoist, and hell a heated garage with plug-in knee warmers would be nice

do u wear pressure braces on ur knees? probably a dumb question but i use em on my wrists for RSI

sounds like u need some bionic knees dude, either that or get em chopped off and get a couple of struts bolted to ur femur and get urself a spare rim and run a single toyo r1r on it...

-D

Carbon 34 Grand Master

Carbon 34

Posted
Posted
ive got a box of baking soda in the kitchen

just trying to work out what mixture to use as the last time i did it , well failed epicly because corrosion is back again ...

Baking Soda is what pro mechanics use with warm water , no real trick to doing it , but you must prevent corrosion by taking that battery out , which by the way its illegal to use a wet cell battery in the boot of your car ADR without proper venting,drain holes. and as you can see , there a crappy battery that farks everything when it spills. buy a gel cell or AGM battery and redo the connectors , no more corrosion from acid

plus the car will thank you by starting easier

boiling water does sweet fark all , unless you want to make things steamy too..lol or if you rinse with it.

you can get a battery spray that coats the terminals with some redish oily crap to seal the corrosion off, might find it in a boat store , haven't seen it in normal car shops here in OZ

heslo Grand Master

heslo

Posted
  • Author
Posted

Good news Luke!

In other news, dropped my head off to Rhemac tonight, wicked set up they have going there, some serious work gets pumped out of there! Bad news is I left there with more options, and unfortunately, more money to spend. It's more of a case as to how far do you go, you need to draw the line somewhere, I just don't know where that is

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...