Jump to content
SAU Community

Recommended Posts

Hey anyone know much about bikes here (possibly ruby, although im talking lil stuff around bikes here)

im planning on getting my mate a pit bike trial bike thingo to use on his farm. doesn’t need to be fast just aslong as it go's and we only light weights so doesn’t need any power.

was looking at possibly one of these but not really sure just yet.

http://cgi.ebay.com.au/125CC-TDR-ALLOY-PIT...=item1e5d39f68a

any bought any of them?

Get one with a Lifan 140cc motor if you can. See my mate Brian at East 50s if you can. He sells better bikes than ebay. Or if ur going ebay, try looking for DHZ bikes.
  • Replies 14.2k
  • Created
  • Last Reply

Top Posters In This Topic

Welcome back blacky. When can i grab my club polo :)

I have it with me and your welcome to come and grab it anytime you want vanilla boy :)

and my jerry can krishdawg

Same applies for you Jose :D

What is the reason for only looking at Duel Solenoid EBC's?

Turbosmart E-Boost 2 would be my choice (infact i bought one a few months to replace my DSBC) but they aren't duel solenoid and they don't need to be.

Electronic%20Boost%20Controllers.jpg

Looked into E boost 2, but at near on $1,000 I'd rather a cheaper option that does exactly the same job.

I don't know much about EBC's, but from my understanding the duel solenoid is better for controlling and holding the boost. Last thing I want is it spiking or dropping off later in the rev range.

Dales right, no need for dual solenoid. Picked up one of the new Eboost Street for the R last year, think it was around $450 not long after release.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...