Jump to content
SAU Community

Removing Boost Restrictor

kikutaknight

By kikutaknight,
in Western Australia

 Share

Recommended Posts

kikutaknight Enthusiast

kikutaknight

Posted
Posted

On the cruise last night, Allen (aka 2LV8ETR) removed the restrictor from Scott's (aka reaper83) car for teh extra boost. 

I believe scott's is a rb26? is that dett? stock turbo? Afterwards he was saying how his stock pressure gauge was hitting max (+7mmHg). I believe +7 is equal to around 14.5 psi, right?

I'm interested in getting more boost out of my car also...but on the rb25det, stock turbo blows up if you push it much more than 12psi, right? what would removing the restrictor in my car do? is it safe?

also...i've ordered a turbotech manual boost controller which i'll be installing once it arrives. also want to know if i'll gain by having the boost controller and the restrictor out.

ty, ty.

Link to comment
https://www.sau.com.au/forums/topic/291921-removing-boost-restrictor/
Share on other sites
SKYRYAN Grand Master

SKYRYAN

Posted
Posted (edited)

I don't think you have a restrictor in the 25

And the boost could be a lot more than that. Don't use factory boost guage when you up the boost. Buy an aftermarket one or use the reading on your electronic boost controllers.

Edited by SKYRYAN
2LV8ETR Mentor

2LV8ETR

Posted
Posted

Only the RB26DETT has the restrictor in it near the PCM, RB25DET's don't.

As far as the RB25DET's are concerned, I wouldn't push one past 12psi safely.

In saying that, V8EATER was caning his RB20DET around pushing 18psi before we dropped the RB26DETT in, but it would only have been a matter of time before the turbo failed.

payback21 Community Regular

payback21

Posted
Posted
Only the RB26DETT has the restrictor in it near the PCM, RB25DET's don't.

As far as the RB25DET's are concerned, I wouldn't push one past 12psi safely.

In saying that, V8EATER was caning his RB20DET around pushing 18psi before we dropped the RB26DETT in, but it would only have been a matter of time before the turbo failed.

I personally think that it would of failed ages ago if i didnt have a electronic boost controller hooked up to it. Electronic boost controllers make a huge difference to the way the turbo spools, spikes etc

We will see how long it lasts when i finish my 4wd beach buggy with the old 20.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm actually not sure - I think it was "Stealth Performance" (It really is near impossible to find a FEMALE 1/8BSPT to 1/8NPT male at ALL) but having the thing leveraged on a 90 degree angle on a small aluminium fitting is not too smart. Also in not too smart, I've drilled out the center of the broken fitting so there's maybe 0.00001mm of thread to bite into, so yeah. I may have to get it drilled/tapped/plugged entirely. Given I could conceivably tap a thread/adapter/pressure line in any point in the oil system I suppose it's feasible to run a line to the Nissan Sensor to keep the dash working. Do these exist in AN fittings and the like? Like an AN fitting that has a NPT (or other?) thread as well for putting a sensor in?
    • sonicii
      Anyone running the VQ37VHR with forced induction?

      By sonicii · Posted

      I would agree.  There will be an amount of boost you could run safely with an otherwise factory system, but it would be low enough to not be worth the cost.  And if you are reliving your 20s, you know a 'little bit' was never enough. Personally, if I didn't want to spend the money, then stick with NA bolt-ons, and maybe a tune.
    • Dose Pipe Sutututu
      Mistakes were made, my R34 Story

      By Dose Pipe Sutututu · Posted

      Fuark, at least the motor survived. What brand was the fitting that snapped?
    • GTSBoy
      Anyone running the VQ37VHR with forced induction?

      By GTSBoy · Posted

      Wrong question. There's no point in spending the rather large sum of cash and effort to add turbo, without taking it to the "sensible" limit of the motor itself. If you have to upgrade injectors, etc, then so be it. That is a tiny fraction of what it will cost you to turbo it.
    • GTSBoy
      Starter motor replacment teeth count.

      By GTSBoy · Posted

      Measure voltage at the starter solenoid terminal when the key is at start and it has clicked. If it is really low, then the suspicion falls on the ignition switch (contacts or wiring thereof) as causing a voltage drop instead of sending enough volts to throw the solenoid all the way to engage the starter itself. If it is a decent voltage, then the suspicion is on the solenoid. Might have s horted coil, or might hva dirty contacts. Rip the starter off, dismantle, clean up contacts and inspect winding. It might not be possible to see if there is a short in the winding though. I have a spare starter here that I could measure the resistance of the coil, as a guide to about what it should be, if you need a comparison. <parts hoarder>No you cannot have it.</parts hoarder>
×
×
  • Create New...