Jump to content
SAU Community

Recommended Posts

Just got the car a couple of weeks ago. At first it only seemed to make the sound when the car was cold, and as soon as i had reversed out the driveway it stopped. Now it seems to be making the sound whenever i push the clutch in and are changing between 1st, 2nd and 3rd gears. Weirdest thing is that it doesn't make the sound all the time just sometimes. Theirs also a burning smell if you jump out the car after driving. As for describing the sound its like a dull squealing, not particularly loud or anything. Also sound stops when you engage a gear.

Anyway if you guys have any ideas at all or could just confirm that's it going to be something that's not too expensive to fix that would be awesome.

Link to comment
https://www.sau.com.au/forums/topic/292484-bad-noise-when-the-clutch-is-in/
Share on other sites

Sounds like your throwout bearing. Depends how bad the sound is, my old S13 used to have a noisy bearing but went away when it was warm . Take it to your mechanic, you may as well upgrade your clutch cos you would be looking at the same labour(just read Burning smell. is your clutch slipping)

I have the same sound too everytime my clutch is in, but the sound is worst especially on gear 2. I guess thats just the clutch burning a bit but anyways its good if you replace your clutch every year to ensure it wont burn aheheh

How long is a piece of string?

Noise will usually get worse and worse before the thing shits itself. If it's just a dull whine for now then you might be safe for a couple thousand km but realistically it can collapse anytime it pleases. Leave it too long and you might start damaging the hydraulic release.

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...