Jump to content
SAU Community

Recommended Posts

Hi all,

I just bought a 1993 Nissan Skyline R32 Coupe (GTS4 RB20DET) and i was wondering what modifications to do on it as I am still a P plater?

The car is basically Lowered, body kit, new heavy duty clutch and rims. Besides that, its all stock.

Any suggestions on what modifications I can do as for now?

Edited by ye.808
Link to comment
https://www.sau.com.au/forums/topic/293731-modification-help/
Share on other sites

Have a read through the forums, lots of info for modifying your Skyline here.

Good to see a new R32 GTS-4 owner on here, it's an awesome car to drive :(

As mentioned above, a turbo back exhaust would be a good place to start. Then you can look at a pod filter and go from there... All depends on how much money you have, there's no shortage of parts out there :(

wow didn't know GTS4's came with a turbo from factory

if that's the case definitely a turbo back exhaust, most systems are cat back only so you would need to source a high flow catalytic convertor and bell mouth dump pipe

then a pod filter with a heat shield or high flow panel filter if you want to keep the stock airbox

also some aftermarket management like a a/f ratio controller or programmable replacement ecu with boost controller

Thanks for the help guys.

Well, I got a pod filter installed on the car now (DRIFT brand) is that any good?

Also, can anyone recommend me a good BOV for an RB20DET which is easily bolted on the crossover pipe (replacing the stock BOV).

A good one which makes a single 'pshhh' sound.

Thanks for the help.

Thanks for the help guys.

Well, I got a pod filter installed on the car now (DRIFT brand) is that any good?

Also, can anyone recommend me a good BOV for an RB20DET which is easily bolted on the crossover pipe (replacing the stock BOV).

A good one which makes a single 'pshhh' sound.

Thanks for the help.

DR/FT...

Ok, lets just say, SAU prefer other brands then anything from Autobarn :(

But if it does the job for you then all good.

To be honest, if you are running stock boost, your stock BOV will be fine.

All those aftermarket BOVs are wank unless you are running a very high level of boost and your stock BOV can't handle the pressure anymore.

+ Now you have an air pod, the pod itself will make some kinda 'Choo' noise after your turbo has spooled and you release the throttle.

Pod filter first. to get the wOooSh sound.. Then a turbo-back exhaust.. not catback' unless u want less power. try justjap.com or gktech.com.au

get stainless steel so down the track you wont need to replace it. then get a front mount intercooler & then finally get a boost controller.. should get you close to 200rwkws.

2nd hand turboback exhaust 500$

intercooler $500

boost controller turbotech - $30

Boost gauge $50

pod filter $100

Edited by richar

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
    • Ok...its taking me long enough to finally do this.  Feck financial security...heart disease will get me soon enough anyway So welcome to the garage..."Clem" Belsil80 has been running a 370Z in Super TT series. So after entering with him in last years Winton 300 i figured I  need my own car. Seems SAU Vic race cars need to be yellow....{tick} Reckon with enough motor i will be able to make up for the lack of talent and stay ahead of the 370Z... but the LS powered S13 and E36s are a ways up the road Aim is to have a car that doesnt stop or turn but has a bit of shed built motor with jam...maybe some cream  First step is getting this ex drift car log booked I am keeping faithful silver car. As the road-club car gets upgrades the race car wil get the sloppy seconds
    • Assuming that they will come off without damage at all.... i would have thought just pull straight up off the spindle with a something or other than can reach underneath. Have you searched for youtube vids of people doing similar on R34s or any other Nissan from the same vintage? They should be the same technique, in all likelihhood.
    • Keeping in mind that sandblasting is really aggressive on softer metals like cast alloy, and you can do damage that you might regret. For trash wheels, not a problem. For wheels with value/scarcity issues, etc.... perhaps a less aggressive media is a better choice?
    • Don't get all high and mighty. Experienced spanner wielders know exactly what effort is required to release an Oof.
×
×
  • Create New...