Jump to content
SAU Community

Recommended Posts

it means as i said earlier... you have either a LEAK or a HEADGASKET problem.

a header tank will not solve this.

if you have done the tests that i and others have mentioned and you are still losing coolant then you have a LEAK or HEADGASKET problem. the heater core which has a flowing path of coolent thro it is one of many possible places for a leak to occur.

stop asking silly questions and start doing some real tests on your car to find the problem.

it means as i said earlier... you have either a LEAK or a HEADGASKET problem.

a header tank will not solve this.

if you have done the tests that i and others have mentioned and you are still losing coolant then you have a LEAK or HEADGASKET problem. the heater core which has a flowing path of coolent thro it is one of many possible places for a leak to occur.

stop asking silly questions and start doing some real tests on your car to find the problem.

I done pressure test no leaking

I changed a cap it doesn't help

the headgasket is fine, because motor is not taking any coolant.

I cleaned the overflow bottle.

I bleeded system

as i said on the topic, it was not losing coolant, the coolant just not fully go back to radiator when cold. I know my question is silly, the problem look very simple, but it just not simple to fix.

Edited by Nosure

did you check the turbo water lines? my s15 in the past (including GTR's) have solid lines i think for water and oil - when under heat, metal expands and moves slightly which can crack the lines

my s15 lost coolant and couldnt figure out why: we pressurised the system and nothing until we put it up onto a hoist and ran the car in-gear = water began leaking out of the turbo water lines.

apparently common; my fix was braided lines to replace the solid ones.

not sure if this is ur problem but though id throw it in anyways, might jst get lucky - all the best mate

-Johnny

did you check the turbo water lines? my s15 in the past (including GTR's) have solid lines i think for water and oil - when under heat, metal expands and moves slightly which can crack the lines

my s15 lost coolant and couldnt figure out why: we pressurised the system and nothing until we put it up onto a hoist and ran the car in-gear = water began leaking out of the turbo water lines.

apparently common; my fix was braided lines to replace the solid ones.

not sure if this is ur problem but though id throw it in anyways, might jst get lucky - all the best mate

-Johnny

thank you, but my turbo is T517Z which is non-water cooled. :(

i have the sae problem as you the car i not loseing coolent what it is doing is when the car gets hot the water expands into the overflow bottle and then when it cools it is only taking about half of it back so when you drive the car a few times it fills the over flow and gets hot cause it not taking the water back

so far i have changed radiator thermostat tryed no themostat changed water pump checked flow through block

the only thing i have left to check is the head gasket i think under load it has a sall leak and is blowing presure into the water side which is overflowing the overflow

Sounds like your head gasket to me??

Is the water mixing in the oil (check oil cap) or oil mixing in the water check rad...

If not any white smoke at all??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...