Jump to content
SAU Community

Recommended Posts

1997 R33 Series 2 120,000kms

I have owned the car for a little over a year, before that it was owned by a friend for a about a year.

Serviced Every 5000km or less with Motul turbo light 10w 40w

Motul Diff Oil

Redline Gearbox Oil

Modifications,

Apexi Power FC Tuned at 12psi (made 201kw)

Blitz Dual SBC boost controller

Split Fire Coil Packs

Walboro Fuel pump

Blitz turbo timer

R34 Turbo (OP6)

RB20 Wastegate Actuator (10 psi)

Split Dump/front Pipe

3in Hi Flow cat (inside not bashed out)

3.5 inch HKS Hi Power Exhaust

Apexi Power intake filter on custom made Metal intake pipe onto the turbo

(Pod not totally boxed in but covered over see photos below)

Standard RRB20 Blow off valve

Greddy Front Mount Inter cooler and piping

Alloy Radiator

Heavy Duty Excedy Clutch

Braided Clutch Line

Braided Brake Lines (ADR approved)

Master cylinder stopper

Front and Rear Strut Braces

Bilstein Shocks and King Springs

Front Whiteline adjustable Castor Bushes (adjustable on car)

Rear Whiteline Camber Bushes

Work Emotions CR KAI 18 x 8.5 in all round

235/35/18 federal 595 SS on the front (70%)

235/35/18 Sumitomo HTR Z 3 on the rear (70%)

Work Wheel Nuts

M Spec side skirts and rear pods

33 GTR rear seat

Have had the Roof lining, A-Pillar and B/C Pillar trims redone in Black Suede (haven't done the sun visors yet)

Only need front GTR seats and interior done

White LEDs' in the cluster

Have Changed the AC Panel, cigarette lighter surround and ignition barrel surround lights all to blue LEDs'

Pioneer Head Deck (DEH-P6850MP)

Pioneer Front Speakers and tweeter

Pioneer Rear 6in Speakers

And finally the rear "Skyline" Boot garnish lights up red with taillights

There is probably more little bits and pieces i have forgotten but i think that will do, Basically the car has never missed a beat in the last 2 years runs great drives beautifully and handles well. Overall i think its one of the nicest R33's running around. Has been my pride and joy for a little over a year but its time for me to move on, Pictures Below feel free to ask any questions.

Price - $18,500 Will get RWC upon Sale

Plates Not Included

PM for my contact details if you are interested

and have a few more photos too

Cheers Scott

post-29410-1258113283_thumb.jpg

post-29410-1258113298_thumb.jpg

post-29410-1258113313_thumb.jpg

post-29410-1258113346_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/296181-1997-r33-series-2/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 2 weeks later...
  • 3 weeks later...
  • 5 weeks later...


  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...