Jump to content
SAU Community

knock sensor on s-afc2

nitemare5

By nitemare5,
in Engines & Forced Induction

 Share

Recommended Posts

nitemare5 Rising Star

nitemare5

Posted
Posted

Just installed a S-AFC II on my r33 gts-t, everything was ok except for the knock sensor. I followed the instructions correctly as far as i know and everything seems to read ok except for the knock sensor, it always sits on 0. I've tried both knock sensors on the ECU and i get the same result. Could it be that my knock sensors are stuffed? or have i just installed it wrong. Any help on the matter would be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/29719-knock-sensor-on-s-afc2/
Share on other sites
gtstii Collaborator

gtstii

Posted
Posted

what sort of knock readings do you get - and does anyone know what constitutes a knock?

I get 0 - 10 on a normal day and up to 20 on a hot day. I know the scale goes up to 200 on the safcII, so these can't be too bad. Would it be like to Power FC scale where above 60 means you are knocking?

Busky2k Veteran

Busky2k

Posted
Posted

Bad readings are when your talking 50+ over the IDLE figure. So if your getting say 20, and its a hot day, and you get 100 (via peak hold) after a WOT blast, then you have knocking. If the peak is only a lil more, then there is nothing to worry about.

Also dw about the idle figures as they rise with temp. NFI why tho. But the engine isnt knocking.

MJ Mentor

MJ

Posted
Posted

I just got mine installed today and i've just been for a drive and the knock goes upto about 10 which seems to be normal. But it takes quite a while for it to move though. I was driving a good 15mins before it moved off 0 on throttle.

However when i was at idle the knock would always read a higher value of 15-20.

strutto Grand Master

strutto

Posted
Posted

Mine was installed today too and so far the highest I've seen is 9 at idle... During a WOT blast it sits on zero?

I've done the knk set a few times but it makes no diff?

Out of curiousity, what are everyones raw knock levels in the knk set menu? (ie 1550, and 3650)

Thanks

MJ Mentor

MJ

Posted
Posted

My knock in the knk set was about 50-60 when i first started the car then after driving it for a while it was upto about 70-90 odd.

what do u mean a WOT blast? In the monitoring menu on acceleration mine sat on 0 for a little while then it started to read figures. But the whole time it was working when the car was idle. Im sure its setup right, perhaps the engine needs to be at operation temp before it gives figures?

Who thought a knock sensor could be so confusing :D

strutto Grand Master

strutto

Posted
Posted

WOT blast = Wide Open Throttle blast.

My knk set readings are pretty much identical: 50-60 to start with, 80-90 after a thrash.

At idle mines the same, between 4 and 10. But when flooring it, 0 all the way to redline? I was only driving for about 30 mins though... I will try it again tomorrow in the heat I guess...

At least I know it's not my crazy switch mod hey... :D

Busky2k Veteran

Busky2k

Posted
Posted

First of all, guys you shouldnt get huge numbers like 80 while idling. Otherwise your calibration is wrong. Go to www.apexi-usa.com to get the SAFC II manual! Btw u need the jap language pack, even tho there is no jap in the PDF? lol

Anyways, the higest ive seen is 20 at idle, but at cruising speeds, its zero which is most important. After a WOT blast i might get 25 or so, which indicates 25 - 20 = 5 knock counts during the WOT blast. Thats nothign to worry about. If its like 80 after the WOT blast, then pinging is at hand!

gtstii Collaborator

gtstii

Posted
Posted

yep - me the same.

- raw figures are 50 - 60.

- idling sits on 0 - 10 on a cool day and maybe 10 - 25 on a 35 degree day.

- when accelerating, car is breathing in cool air from outside the engine bay and comes down to 0 (maybe 10 on a hot day)

it would be good though to speak to apexi and ask for some guidance on what level a knock is (ie 50 or 100?)

I know that Access Auto's in Vic is Apexi's Australian distributor and they have technicians that you can talk to if you bought the product in Australia (ie not imported from japan).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Marek
      Hi everyone.

      By Marek · Posted

      Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
    • soviet_merlin
      Ethanol Content Sensor - Always at 11%?

      By soviet_merlin · Posted

      Oh, you are right. But, in Australia E10 is based on 91RON fuel and ends up being 94RON. Hence it being the cheaper option for economy cars. The more performance oriented cars go for the 98RON fuel that has no ethanol mixed in. The only step up we have left then at some petrol stations is E85.
×
×
  • Create New...